Kemppi SuperSnake GTX Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 35

Kemppi SuperSnake GTX Скачать руководство пользователя страница 18

SuperSnake GTX

Operating manual - EN

2.4 Installing subfeeder into protective frame

The protective frame provides support and protection for the subfeeder itself as well as for the cables connected.

All of the subfeeder cables should be connected before installing the subfeeder into the protective frame.

1.

Place the protective frame on a flat surface upside down and open the bottom hatch.

>> To release the locking mechanism, pull the latches on one side towards the center and lift that side up.

2.

Lift the fully connected subfeeder upside down into the protective frame. Ensure that:

>> The Euro connector housings in both ends of the subfeeder sits firmly on the pads in the protective frame.
>> The groove in the interconnection cable collar aligns with the support bracket in the end of the protective

frame.

3.

Close the hatch so that the locking mechanism latches lock properly in place. Ensure that:

>> The cables are routed properly and don't get caught between the frame and the hatch.
>> The supports incorporated in both ends of the hatch provide additional support for the main cables.

© Kemppi

18

1921930 / 2144

«
...
16
17
18
19
20
...
»

Содержание SuperSnake GTX




































Отзывы:

Нет отзывов