background image

Kempact mig 50 / 0635 – 11 

© Kemppi oy

8. TERMS OF GUARANTEE

Kemppi  Oy  provides  a  guarantee  for  products  manufactured  and  sold  by  them  if  defects  in 

manufacture and materials occur. Guarantee repairs must be carried out only by an Authorised 

Kemppi Service Agent. Packing, freight and insurance costs to be paid by orderer. The guarantee is 

effected on the date of purchase. Verbal promises which do not comply with the terms of guarantee 

are not binding on guarantor. 

Limitations on guarantee

The following conditions are not covered under the terms of guarantee: defects due to natural wear 

and tear, non-compliance with operating and maintenance instructions, connection to incorrect or 

faulty supply voltage (including voltage surges outside equipment spec.), incorrect gas pressure, 

overloading, transport or storage damage, fire of damage due to natural causes i.e. lightning or 

flooding.

This guarantee does not cover direct or indirect travelling costs, daily allowances or accommodation. 

Note: Under the terms of guarantee, welding torches and their consumables, feeder drive rolls and 

feeder guide tubes are not covered. Direct or indirect damage due to a defective product is not 

covered under the guarantee. The guarantee is void if changes are made to the product without 

approval of the manufacturer, or if repairs are carried out using non-approved spare parts. 

The guarantee is also void if repairs are carried out by non-authorised agents.

Undertaking guarantee repairs

Guarantee defects must be informed to Kemppi or authorised Kemppi Service Agents within the 

guarantee period. Before any guarantee work is undertaken, the customer must provide proof of 

guarantee or proof of purchase, and serial number of the equipment in order to validate the guarantee. 

The parts replaced under the terns of guarantee remain the property of Kemppi. 

Following the guarantee repair, the guarantee of the machine or equipment, repaired or replaced, 

will be continued to the end of the original guarantee period.

Содержание KEMPACT MIG 2520













Отзывы: