KEMEL EVK2RV Скачать руководство пользователя страница 5

Страница: 5 / 13

－

[D] Handling

1 Preparation before running

(1)Make sure to purge air in the inflatable ring on the pressure gauge(G-1) by closing

valve

①

and opening valve

②

(2)Purge air in the casing by opening plug

③

. And close plug

③

(3)Open valve

④

(4)Begin running of the cooling water pump.

2 Handling procedure of the inflatable ring

This seal is to be used in the inspection or replacement of a seal ring at sea.

In working with this seal, make sure the shaft does not rotate.

Handling procedure is as follows.

(1)Stop the propeller shaft.
(2)Close valve

④

and valve

②

(3)Open valve

①

gradually so that the air pressure becomes 0.3

～

0.6 MPa in

Gauge(G-1).

(4)Open plug

③

and make sure of no water leakage from the casing.

(5)Remove the mating ring and inspect the seal ring . If necessary, replace it.
(6)After work, the reverse procedure should be performed. At this time, reconfirm

closure of valve

①

, and opening of valve

②

(7)Purge air in the casing by opening plug

③

. And close plug

③

Plug

SEALING

From air source

①

G-1

②

④

10mm CuT

G-2

Normally open

Normally close

Fig.-2

From water pump

Shaft rotation must be stopped before operating the inflatable ring.

CAUTION!

Содержание EVK2RV














Результаты поиска

Содержание EVK2RV

Отзывы:

Похожие инструкции для EVK2RV

Бренды по названию

Популярные бренды

KEMEL EVK2RV, Инструкция по эксплуатации

Результаты поиска

Содержание EVK2RV

Отзывы:

Похожие инструкции для EVK2RV

Бренды по названию

Популярные бренды