Kelvin Mini Series Скачать руководство пользователя страница 26

Страница: 26 / 29

3.2 Check oil level

3.3 Check noise

3.4 Change oil

Wheel

4.1 Remove the rope and debris from the wheel

4.2 Check the drive wheel wear and bolts

4.3 Remove and lubricate the wheel bearing

Brake

5.1 Clean the brake part

5.2 Check the wear of the brake pads

5.3 Check the brake condition when the brake is released

Controller board

6.1 Cleaning and installation inspection

6.2 Fix the cable connector tightly

6.3 Check the contactor contacts

Battery

7.1 Check the electrolyte level (the level should be 10-

15mm above the plate)

7.2 Check whether the connection between the battery

forklift and the charger is tight

7.3 Check each battery and its insulation sheath

7.4 Check the electrolyte specific gravity and temperature

7.5 Clean the battery

Hydraulic system

8.1 Check the pipeline and joints for leaks

8.2 Check the pipeline wear

8.3 Check the fuel tank for leaks

8.4 Check the oil level

8.5 Oil change

Cylinder

Содержание Mini Series






























Результаты поиска

Содержание Mini Series

Отзывы:

Похожие инструкции для Mini Series

Бренды по названию

Популярные бренды

Kelvin Mini Series, Инструкция по техническому обслуживанию

Результаты поиска

Содержание Mini Series

Отзывы:

Похожие инструкции для Mini Series

Бренды по названию

Популярные бренды