background image

 

 

11 

 

 
 
 
2.4 The maximum noise value of the ear of the forklift truck is not more than 80dB (A). The test method is according 
to JB/T3300; the vibration is not more than 0.4m/s2. The uneven road surface will increase the noise and vibration. 

3. Steering 

3.1 Steering is controlled by the steering wheel. The forklift is a speed-following type electric steering. The faster 
the steering wheel rotates, the faster the steering wheel turns. When the steering wheel is reversed, the steering 
wheel also reverses. 
3.2 When the forklift encounters an obstacle, it should not be forced to pass and should pass by the obstacle. 

Warning

ʄ

 

Do not allow wheels to slip. 
If the operator's hands or shoes are stained with oil, it is easy to operate error and cause the forklift to lose control, 
so you should clean your hands and shoes before driving. 

4. Parking 

4.1 Release the accelerator. 
4.2 Make direction switch to the middle. 
4.3 Reduce the fork to the lowest position so that there is no system pressure in the hydraulic system. 
4.4 Turn off the key switch. 
4.5 Press the emergency stop switch. 
 

Warning

ʄ

 

Do not allow unauthorised driving. 
If you leave, take the key with you. 

 

 

 

 

 

 

 

 

 

Содержание Mini Series






























Отзывы: