manualshive.com logo in svg

Keithley 8011, Инструкции по подключению, Страница: 10 / 16

Поделиться
Скачать
Keithley 8011 Скачать руководство пользователя страница 10

Model 8011 Connection Instructions 

 

10 

PA-1032 Rev. A / April 2011 

 

Three-terminal DUT using a Model 2651A and a single or dual channel 
SourceMeter instrument 

NOTE

 

If you are using a Model 2600A, do not set the output above 40 V. The Model 8011 is rated to 40 V. 

You can use the Model 8011 with the 8010-120 board to test a three-terminal device using a Model 2651A High 
Power System SourceMeter

®

 Instrument and another SourceMeter instrument. This use-case is appropriate for the 

following SourceMeter instruments: 

•

 

Model 2601A Single-Channel System SourceMeter Instrument 

•

 

Model 2611A Single-Channel System SourceMeter Instrument (200 V) 

•

 

Model 2602A Dual-Channel System SourceMeter Instrument 

•

 

Model 2612A Dual-Channel System SourceMeter Instrument (200 V) 

Tools and equipment needed 

•

 

Small flat-head screwdriver 

•

 

Cable created using the 2600-KIT screw terminal connector kits (included with the Model 8011); the cable must 
use wire that can support 3 A and 200 V 

Instructions 

1.  Remove power from the SourceMeter instruments. 

2.  Make connections as shown in Table 3 and Figure 7. 

3.  Install the three-terminal DUT into the socket on the 8010-120 board. 

4.  Return power to the SourceMeter instruments. 

5.  On both SourceMeter Instruments: 

a. Press 

the 

CONFIG

 key. 

b. Press 

the 

SRC 

or 

MEAS 

key (the sense mode can be set from either the V-SOURCE or the V-MEAS 

menu). 

c.  If you pressed the SRC key, select 

V-SOURCE > SENSE-MODE

. 

d.  If you pressed the MEAS key, select 

V-MEAS > SENSE-MODE

. 

e. Select 

4-WIRE

 to enable remote sense. 

6.  Test the device. 

 

Содержание 8011

















Отзывы:

Нет отзывов