manualshive.com logo in svg

Keithley 7711, Руководство пользователя

Поделиться
Скачать
Keithley 7711 Скачать руководство пользователя страница 25

21

Private Sub Take_Measurements()
    Dim I, J As Integer
    Dim Channel_Num As Integer
    Dim Channel_Str As String
    Dim Reading As String
    
    For I = 1 To NUMBER_OF_DUTS                                             ' Loop to take measurements for all DUTs.
        Channel_Num = (SLOT_7711 * 100) + I                                 ' Determine channel number.
        Channel_Str = "(@" & CStr(Channel_Num) & ")"                        ' Convert channel to ASCII string parameter.
        Call send(ADDRESS, "ROUT:MULT:CLOS " & Channel_Str, Status)         ' Route channel on 7711 to Out A.
              
        For J = 1 To NUMBER_OF_FUNCTIONS                                    ' Loop for each measurement function.
            Channel_Num = (SLOT_7700 * 100) + J + ((I - 1) * NUMBER_OF_DUTS)
            Channel_Str = "(@" & CStr(Channel_Num) & ")"
            Call send(ADDRESS, "ROUT:CLOS " & Channel_Str, Status)          ' Close measurement channel on the 7700.
            Call send(ADDRESS, "READ?", Status)                             ' Take measurement.
            Call enter(Reading, MAXLEN, LENGTH, ADDRESS, Status)
            
            Readings(Reading_Counter) = Reading                             ' Store reading.
            Reading_Counter = Reading_C 1
        Next
        
        ' Insert code here to take oscilloscope measurements.
    Next
End Sub

'' ---------------------------------------------------------------------------------------------------------------------
'' Main Function
'' ---------------------------------------------------------------------------------------------------------------------
Private Sub Start_Click()
    Reading_Counter = 0                                                   ' Reset index counter.
    Call settimeout(ENTER_TIMEOUT)                                        ' Set timeout valuefor enter function.
    
    Call initialize(21, 0)                                                ' Initialize GPIB.

    Call send(ADDRESS, "*RST", Status)                                    ' Restore *RST defaults.
    Call send(ADDRESS, "INIT:CONT OFF", Status)                           ' Ensure INIT continuous trigger is off.
    Call send(ADDRESS, "FORM:ELEM READ,UNIT", Status)                     ' Display only reading and units.
    
    Call Configure_7700_Channels                                          ' Setup measurement channels on 7700.
    Call Configure_Power_Supplies(HIGH_LINE, TEN_PERCENT_LOAD)            ' DUT input voltage is high line and 10% load.
    Call Take_Measurements
    Call Configure_Power_Supplies(HIGH_LINE, NINETY_PERCENT_LOAD)         ' DUT input voltage is high line and 90% load.
    Call Take_Measurements
    Call Configure_Power_Supplies(LOW_LINE, TEN_PERCENT_LOAD)             ' DUT input voltage is low line and 10% load.
    Call Take_Measurements
    Call Configure_Power_Supplies(LOW_LINE, NINETY_PERCENT_LOAD)          ' DUT input voltage is low line and 90% load.
    Call Take_Measurements
End Sub

Содержание 7711







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды