manualshive.com logo in svg

Keithley 7022, Инструкция по эксплуатации

Поделиться
Скачать
Keithley 7022 Скачать руководство пользователя страница 78

Service Information

6-10

Channel functionality test

1. As shown in Figure 6-8, connect the suspect input or

output channel to an output or input channel that is
known to be functioning properly. The internal 5V
supply must be used.

2. From the front panel of the mainframe, turn on (close)

the output channel. Verify that the display indicates that
the output channel is on (closed). Keep in mind that the
output can be high (positive) or low (negative) when the
channel is turned on, depending on the logic
configuration.

3. Place the mainframe in the “read input channels” dis-

play mode. Verify on the display that the input channel
is off (open).

4. On the mainframe, turn off (open) the output channel

and verify on the display that the input channel turns on
(closes).

5. On the mainframe, return the instrument to the normal

display mode and verify on the display that the output
channel is off (open).

Figure 6-8

Testing an input or output channel

WARNING:

NO INTERNAL OPERATOR SERVICABLE PARTS,SERVICE BY QUALIFIED PERSONNEL ONLY.

WARNING:

NO INTERNAL OPERATOR SERVICABLE PARTS,SERVICE BY QUALIFIED PERSONNEL ONLY.

CAUTION:

FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,REPLACE FUSE WITH SAME TYPE AND RATING.

CAUTION:

FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,REPLACE FUSE WITH SAME TYPE AND RATING.

!

115V

!

90-110V

105-125V

180-220V

210-250V

A

B

C

1

3

4

5

6

2

Model 7022

H

  Model 6517A

  Model 7025
  Unterminated
  Triax Cable

(Red)

Banana to Banana Cable

Unterminated
Banana Cables

Source V and
 Measure V/I

H

Columns

Jumpers

(1 of 5)

Rows

H L

H L

H L

H L

H L

H L

H

L

H

L

H

L

D

H

L

E

H

L

Chassis Ground
is accessible
at 7001/7002 rear
panel

Ground Link

Removed

Figure 6-7

Common-mode isolation testing

Output Channel

Internal connections:

Internal voltage source (+5V) selected.
Pull-up resistor installed.

OUT

GND

Input Channel

IN

GND

Artisan Scientific - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisan-scientific.com

Содержание 7022












































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды