manualshive.com logo in svg

Keithley 7022, Инструкция по эксплуатации

Поделиться
Скачать
Keithley 7022 Скачать руководство пользователя страница 45

Card Connections and Installation

4-11

Typical matrix connection schemes

The following information provides some typical connection
schemes for single-card, two-card, and two-mainframe sys-
tem configurations. Connection schemes for the multi-pin
connector card use some of the techniques presented in this
section.  Keep in mind that these are only examples to dem-
onstrate various ways to wire a test system. 

Single-card system

Figure 4-12 shows how external connections can be made to
a single-card system that uses the multi-pin connector card.
Instrumentation and DUT are hard-wired to the Model
7011-MTR male bulkhead connector. This connector has
solder cups that will accept wire size up to #24 AWG. The
test  system  is  connected  to  the  matrix  using  the  Model
7011-MTC-2   round   cable   assembly.   This   cable   mates

directly to both the external bulkhead connector and the
Model 7022. Notice that the bulkhead connector is shown
mounted to a fixture to help keep the cabling stable during
the test.

When using a single-card system, make sure that the card
remains electrically isolated from any other switching cards.
There are several ways to ensure isolation for a single card in
the Model 7001/7002 mainframe: 

1. Vacate the adjacent slot in the mainframe. If there is a

Model 70XX card installed in the other slot, remove it.

2. Remove the backplane jumpers on the card. This will

disconnect the card from the analog backplane of the
mainframe.

3. Remove the backplane jumpers from the switching card

installed in the adjacent slot.

7022

DUT Test Fixture

1

2

3

4

5

6

Instrument

Instrument

Instrument

Instrument

Row B

Row C

Row D

Row E

1

2

3

4

5

6

DUT

1

2

3

4

5

6

A

B

C

D

Equivalent Circuit

Columns

Rows

Fixture for

Bulkhead

Connector

7011-MTR

Bulkhead

Connector

7011-MTC-2

Cable Assembly

22 Individual Conductors

Instrument

Row A

E

Instruments

Figure 4-12

Single-card system example

Artisan Scientific - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisan-scientific.com

Содержание 7022












































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды