Keithley 2010 Скачать руководство пользователя страница 113

Страница: 113 / 134

:NDUE (:CALibration:PROTected:NDUE)

Purpose

To send the next calibration due date to the instrument.

Format

:cal:prot:ndue <year>, <month>, <day>

Parameters

<year>

= 1995 to 2094

<month>

= 1 to 12

<day>

= 1 to 31

Query format

:cal:prot:ndue?

Response

Description

The :NDUE command allows you to store the date when calibration is next
due in instrument memory. You can read back the next due date from the
instrument over the bus by using the :NDUE? query or the front panel CAL
menu.

Note

The next due date parameters must be delimited by commas.

Examples

:CAL:PROT:NDUE 1996,12,16

Send due date (12/16/96).

:CAL:PROT:NDUE?

Request due date.

Calibration Command Reference

B-7

Содержание 2010






































































































































Результаты поиска

Содержание 2010

Отзывы:

Похожие инструкции для 2010

Бренды по названию

Популярные бренды

Keithley 2010, Руководство по обслуживанию

Результаты поиска

Содержание 2010

Отзывы:

Похожие инструкции для 2010

Бренды по названию

Популярные бренды