10
AIR300 LEG EXTENSION PRO
OPERATION MANUAL
LINE 1 - RESISTANCE
The Resistance window displays the current resistance or OFF. Adjust the resistance using the (+/-) Thumb Buttons located
on either side of the Seat. When the window displays OFF, the machine enters a low power consumption sleep mode to
increase battery life. Normal operation may be resumed by pressing either Thumb Button or by inserting the eChip. If this
window displays t
he low battery signal (“Lo-bA”)
, the batteries are getting weak and should be replaced soon (D batteries,
quantity 2; refer to page 16 “Battery Replacement” for complete instructions).
LINE 2 - SET OR REPETITIONS
This window displays the current repetition count except immediately after an eChip is first inserted, in which case it displays
the current set. The set count may range from 1 to 9 and is signaled by the appearance of three horizontal bars in the left
digit. The number of sets is defined as the number of sets of exercises performed in a four-hour period. Once four hours have
passed, the machine assumes that the user is returning for a new visit. The repetition count may range from 0 to 99. The
repetition count may be reset by momentarily pressing both increase and decrease (+/-)Thumb Buttons simultaneously. In
Power Test mode, the window will display the repetition count per test section (refer to page 14 “Power Test” for complete
instructions).
LINE 3- TARGET REPS
The Target Reps window displays the number of repetitions performed on the corresponding set of the previous visit, if that
set was a normal workout set and an eChip is inserted. If the corresponding set of the previous visit was a Power Test, the
display will show “Pr.” When in Power Test mode, the window will display “P1” during the low resistance test set and “P2”
during the high resistance test set (refer to page 14 “Power Test” for complete instructions).
LINE 4 - CURRENT POWER / PERCENT OF PEAK POWER
The Current Power window can display 4 different values. During an exercise set, it displays the percent of peak power
achieved for the most recent repetition. At the end of a Power Test, this window displays the resistance to use to achieve
maximum power. When an eChip is inserted and the previous corresponding set was a normal workout set, it displays the
resistance used for that set. When an eChip is inserted, and the previous corresponding set was a Power Test, it displays the
resistance to use to achieve maximum power. When the calculated resistance to achieve maximum power is being displayed,
it flashes. In summary, during an exercise set, this window displays the power for the current rep, at the end of a Power
Test it is the resistance to use for training at maximum power; when an eChip is inserted it is the resistance to set into the
window above before exercising.
LINE 5 - PEAK POWER
The Peak Power window displays the highest power that has occurred during this workout or since the data was last reset.
LINE 6 - MACHINE ADJUSTMENT
When using the eChip, the Seat position (fore or aft position, 16 settings) can be tracked and recorded. Press the arrows
located directly above/below each window to input settings.
NOTE: The adjustment may only be changed immediately after the eChip is inserted and before the third repetition has
occurred. Once three repetitions are performed, the machine adjustments cannot be changed until the eChip has been
removed and reinserted. The machine adjustment applies to a machine and cannot be changed from set to set.
LINE 7 - eCHIP READER
The eChip Reader, located at the bottom right of the Power Display, receives and reads your eChip data.
LINE 8 - eCHIP
The eChip collects workout data and can store up to 24 separate equipment models (up to 4 equipment position settings per
model) and up to 240 separate workout sets across Keiser Air and Infinity Series. Designed as an electronic replacement for
the hand-written exercise card, the eChip enables recall and set-up of the exercise equipment upon the next workout. The
Keiser eChip software allows saved eChip data to be viewed, stored, and exported (.csv file format) for analysis.
NOTE: Three user eChips (red color) come standard with your Air300 Leg Extension Pro. The Keiser USB Power Kit (a USB adapter
to transfer data from your eChip to your computer and Time Set eChips to set the time zone/time on your Air300 Leg Extension
Pro) is available. For parts order, contact Keiser Customer Support (see back cover for contact information).
Keiser eChip software system requirements, download, and user manual available at keiser.com/support
(search: eChip).
DISPLAY FEATURES
