Installing the KE2 LDA: Option 2
Connecting Serial Devices Only
EACH DEVICE MUST HAVE A SEPARATE/
UNIQUE MODBUS ADDRESS
(See Appendix B for instructions)
Connect Customer Network
STATUS
All Clear
Evaporator Fan
Off
Plug power cable into the KE2 LDA
and the other end into an electrical outlet.
The unit will power on automatically.
Connect wirelessly
to the LDA Network
ABC Contracting
(888)555-3358
System Mode
Cool
Superheat
0.0 F
Suct Pressure
96.2 F
Suct Temp
87.7 F
WAN
Power
LAN
MODIFY
STATUS
ABC Contracting
(888)555-3358
All Clear
Compressor
On
System Mode
Cool
Evaporator Fan
Off
Room Temp
-8.5 F
Coil Temp
15.4 F
Sat Temp
46.0 F
Superheat
0.0 F
Valve Position
Manual
Suct Pressure
96.2 F
Suct Temp
87.7 F
Dig Input 3
Dis
Defrost
Off
Aux Temp
Dis
Dig Input 1
Closed
Dig Input 2
Dis
WiFi to PC/Laptop,
Tablet, Phone
Serial-Modbus Controllers:
KE2 Temp, KE2 Low Temp
KE2 Adaptive Control
.
Hold for manual defrost
therm
solutions
KE2
Temp
Hold for manual defrost
therm
solutions
KE2
Temp
.
Q.5.42 November 2016
Page 2
KE2 Local Area
Dashboard & Alarms
Overview, Installation, and Setup Instructions
© Copyright 2016 KE2 Therm Solutions, Inc., Washington, Missouri 63090
Connect Customer Network
All Clear
Evaporator Fan
Off
Connect wirelessly
to the LDA Network
ABC Contracting
(888)555-3358
System Mode
Cool
Superheat
0.0 F
Suct Pressure
96.2 F
Suct Temp
87.7 F
WAN
Power
LAN
.
KE2
Evaporator
Efficiency
TM
therm
solutions
ENTER
BACK
.
KE2
Evaporator
Efficiency
TM
therm
solutions
ENTER
BACK
.
Ethernet Controllers:
KE2 Evaporator Efficiency,
KE2 Evap for Rack Efficiency,
KE2 Controlled Environment
NOTE: DHCP or Static IP in
Customer Network
Plug power cable into the KE2 LDA
and the other end into an electrical outlet.
The unit will power on automatically.
KE2
Evaporator
Efficiency
TM
therm
solutions
ENTER
BACK
.
WiFi to PC/Laptop,
Tablet, Phone
Serial-Modbus Controllers:
KE2 Temp, KE2 Low Temp
KE2 Adaptive Control
.
Hold for manual defrost
therm
solutions
KE2
Temp
Hold for manual defrost
therm
solutions
KE2
Temp
.
•
KE2 Evaporator Efficiency, KE2 Evap for Rack Efficiency,
or KE2 Controlled Environment
•
DHCP Enabled or set address from
192.168.50.2 to 192.168.50.99
•
Check IP address from front panel if DHCP
•
Factory assigned 10.10.x.x addresses are now visible when
connected to the LAN port. However, 10.10.x.x controllers can
only be managed by PC, phone, or tablet when wirelessly
connected to the KE2 LDA.
Installing the KE2 LDA: Option 1
Connecting Using the KE2 LDA as a
Permanent WiFi Service Tool
EACH DEVICE MUST HAVE A SEPARATE/
UNIQUE MODBUS ADDRESS
(See Appendix B for instructions)
