When necessary
在必要時
23
SM30H
要求維修服務前，請檢查以下項目。如果問題仍然存在，請拔除 AC 配接器的電源及底座上的機身連接插頭，然後聯絡零售商安排維修。
故障現象
檢查
按開／關鈕啟動時扇葉不轉動。
․
AC 配接器是否已經完全及正確地連接？
․
保護網是否變了形，或碰到扇葉？
․
[ 兒童安全鎖 ] 指示燈亮起了嗎？（20 頁）
․
溫度感應器運作是否被設為「開」？（21 頁）
扇葉轉動時發出異常聲音。
․
扇葉及保護網是否已經正確地安裝？（8-9 頁）
․
保護網是否變了形，或碰到扇葉？
按鈕後電風扇沒有運作。
․
[ 兒童安全鎖 ] 指示燈亮起了嗎？（20 頁）
遙控器沒有反應。
․
保護膠紙是否已經被拿走？（12 頁）
․
電池是否無電？（12 頁）
․
電池是否已經正確地安裝？（22 頁）
nanoe
TM
( 納米離子 ) 出風口發出異
常聲音。
․
nanoe
TM
( 納米離子 ) 運作時會發出微弱的聲音。因應不同情況或組合運作模式，
nanoe
TM
( 納米離子 ) 產生部會發出響亮或極微弱的聲音。這並非故障。
►
如果感到煩擾，請關閉 nanoe
TM
( 納米離子 ) 運作。
（15 頁）
雖然已經設定溫度感應器運作，
但電風扇沒有按照設定的溫度運作。
․
室溫會因應所在地點而有所不同。它可能會與溫度計所顯示的有差別。
（21 頁）
左右擺動角度變窄。
․
用手或任何物件阻礙電風扇擺動可導致運作異常。
►
關機再開機，電風扇即正常擺動。
電風扇停止運作。
․
按住任何按鈕 8 秒，電風扇會基於安全理由而關閉。按一下開／關鈕，電風扇便會恢復運作。
所有 [ 風速 ] 指示燈都閃爍。
․
電風扇運作時是否有異物碰到扇葉，使它停止了轉動？
►
1
拔除 AC 配接器的電源。
2
拿走使轉動停止的異物。
3
連接 AC 配接器，然後再次開啟電源。
如果出現以下情況，請立刻聯絡零售商。
[ 溫度感應器 ] 指示燈閃爍。
․
溫度感應器發生故障。
►
聯絡零售商安排維修。
Before requesting service, please check the following. If the problem still persists, disconnect the AC adaptor from power supply, and the
main body connection plug from the base, and then contact the dealer for repairing.
Symptom
Check
The blade does not rotates when
pressing Off/On button to start.
• Is the AC adaptor connected fully and correctly?
• Is the guard deformed, or does it hit the blade?
• Is Child lock lamp lit? (P.20)
• Is Temp. Sensor operation controlled at “On”? (P.2
1
)
The blade rotates, but abnormal
sound is heard.
• Are the blade and guards installed correctly? (P.8-9) • Is the guard deformed, or does it hit the blade?
The fan does not operate with the
button pressed.
• Is Child lock lamp lit? (P.20)
The remote control does not
function.
• Is the protective plastic sheet removed? (P.12)
• Is the battery exhausted? (P.12)
• Is the battery installed correctly? (P.22)
Abnormal sound is heard from the
nanoe
TM
emission outlet.
• During nanoe
TM
operation, faint sound is heard. According to the circumstances or combined
operation mode, it may sound loud or too faint. It is not malfunction.
►
If it is annoying, turn off nanoe
TM
operation. (P.15)
Although Temp. Sensor operation
is set, the fan does not operate
based on the temperature.
• Room temperature differs by its location. It may be different from the indication of your
thermometer. (P.21)
Horizontal swing angle become
small.
• Clogging swing operation by hand or any objects, abnormal operation may occur.
►
Turning off and turning on again, the fan operates normally swing.
The fan stops operation.
• When pressing and holding any buttons for 8 seconds, the fan turns off for safety. The fan
resumes operation with Off/On button pressed.
All [Speed] lamps blink.
• Does foreign object hit and stop the rotation of blade during operation?
►
1
Disconnect the AC adaptor from power supply.
2
Remove the foreign object stopping the rotation.
3
Connect the AC adaptor and turn on again.
Please contact the dealer immediately in the case below.
[Temp. Sensor] lamp blinks.
• Temperature sensor is malfunctioned.
►
Contact the dealer for repairing.
排解疑難
Troubleshooting
