manualshive.com logo in svg

KBL megaSun 6900 a deluxe, Руководство по сборке

Сборочная инструкция для солярия KBL megaSun 6900 Deluxe доступна для скачивания бесплатно на manualshive.com. Этот роскошный солярий обладает мощными функциями и стильным дизайном. Скачайте руководство пользователя, чтобы быть уверенным в правильной сборке и использовании этого профессионального солярия.

Поделиться
Скачать
background image

A s s e m b l y   I n s t r u c t i o n s

 

|

 6808 /7908

35

5.6 Install the bench

PH2

  3

5.6.1 REMOVE CANOPY PANE

• Lift out canopy panel (temporarily). Similar to dis-

assembling step (4.3.4).

5.6.2 INSTALL THE BENCH

• The installing of the bench is similar to the disas-

sembling steps (4.7).

5.7 Install front panel

PH2

5.7.1 INSTALL FRONT PANEL

• The  installation  of  the  front  panel  is  similar  to  the 

disassembling steps (4.5).

5.7.2 ADJUST THE BENCH LOCK

• Coarse adjustment of the bench lock. Details under 

fi ne adjustment of the bench lock -> 5.14.

Remove all protective fi

 lm!

5.7.3 INSTALL BOTTOM SEALS 

5.7.4 CLOSE THE BENCH

5.8 Install bench pane

PH2

Remove protective fi lm on the bottom!

• The fi lm on the top stays on until after 

aquaCool initialisation.

5.8.1 INSTALL BENCH PANE

• The installation of the bench pane is similar to the 

disassembling steps (4.4).

5.8.2 INSTALL DUCTING PANE

• The installation of the ducting pane is similar to the 

disassembling step (4.3.6).

Remove all protective fi lm!

Center-align  the  ducting  pane  so  that 

the bench pane can move freely.

5.8.3 CLOSE THE BENCH PANE.

5.8.4 RE-INSTALL THE CANOPY PANE.

• Install the canopy pane  > similar to disassembling 

step 4.3.4.

• Connect interior control panel -> similar to disas-

sembling step 4.3.2.

• Clean inside of canopy pane.

Содержание megaSun 6900 a deluxe













































Отзывы:

Нет отзывов

Похожие инструкции для megaSun 6900 a deluxe

Бренды по названию

Популярные бренды

Загрузить еще бренды