manualshive.com logo in svg

KBL megaSun 6900 a deluxe, Руководство по сборке

Сборочная инструкция для солярия KBL megaSun 6900 Deluxe доступна для скачивания бесплатно на manualshive.com. Этот роскошный солярий обладает мощными функциями и стильным дизайном. Скачайте руководство пользователя, чтобы быть уверенным в правильной сборке и использовании этого профессионального солярия.

Поделиться
Скачать
background image

A s s e m b l y   I n s t r u c t i o n s

 

|

 6808 /7908

24

4.8.3 RELEASE TENSION ON THE CANOPY

CAUTION

Components are under spring tension

Risk  of  injury  by  the  canopy  dropping 
down  when  releasing  the  tension  of  the 
canopy lifting mechanism.

•  The  canopy  must  be  held  by  a  second 

person to prevent it from dropping down.

• Support the canopy in the center (second person).

• Release tension of the canopy lifting mechanism.

19

PH2

• Turn  the  adjusting  nuts  on 

both  sides

  one  after 

another up to the beginning of the threaded bar.

• Take 

both

 steel ropes of the canopy lifting mecha-

nism off the guide pulleys.

• 

• Unhook the spring.

• Lower canopy. 

4.8.4 REMOVE REAR PLASTIC CLADDING

The rear plastic cladding is loosely fi tted 

in all 

7908

 tanning devices.

6808

  devices 

with

  rear  plastic  cladding 

have  3  additional  black  screw  rivets  to 

loosen.

PH2

In 

6808

 devices 

without

 rear plastic clad-

ding, this is replaced with a sheet metal 

plate which cannot be removed.

Содержание megaSun 6900 a deluxe













































Отзывы:

Нет отзывов

Похожие инструкции для megaSun 6900 a deluxe

Бренды по названию

Популярные бренды

Загрузить еще бренды