KBC WESII Series Скачать руководство пользователя страница 117

Страница: 117 / 141

WESII User Manual

Manual-WESII-Rev1403
Copyright © KBC Networks 2014

Page 116 of 140

www.kbcnetworks.com

System: DEVICE MAINTENANCE

Reboot:

this performs a re-boot to the unit, this can take up to 1 minute to perform.

Reset to defaults:

In this menu option the unit can be soft rebooted or reset to

defaults.

The default configurations are as follows:

Host/AP LAN Configuration:

192.168.1.200

255.255.255.0

No Gateway IP

Client LAN Configuration:

192.168.1.201

255.255.255.0

No Gateway IP

Interface Access Username:

admin

Interface Access password:

admin

Hostname:

AP (for the Host/AP)

CLIENT (for the Client)

Remote Client-Lock to MAC:

00:00:00:00:00:00

Local AP-ESSID:

KBC-WESII

Country Code:

USA (North America)

Select Country (all other countries)
Wireless Profile:

NA (IEEE802.11n & IEEE802.11a)

NG (IEEE802.11n, IEEE802.11 g)

NY (IEEE802.11n & IEEE802.11y)

Channel Spectrum Width:

20/40M

Channel-Frequency:

set to auto-select

Transmit Power:

23 dBm (North America)

19 dBm (all other countries)

Local AP WPA Cipher:

AES

Local AP Preshared Key:

11111111

Long Range Parameters:

Enabled

RSSI LEDs:

LED1=10;

LED2=20;

LED3=30; LED4=40

The Administrator Username can also
be changed. It does not need to be
‘admin’ to change the password.

The default password is ‘admin’

Change the password here and verify
below

Содержание WESII Series














































































































































Результаты поиска

Содержание WESII Series

Отзывы:

Похожие инструкции для WESII Series

Бренды по названию

Популярные бренды

KBC WESII Series, Руководство пользователя

Результаты поиска

Содержание WESII Series

Отзывы:

Похожие инструкции для WESII Series

Бренды по названию

Популярные бренды