KBC WESII Series Скачать руководство пользователя страница 113 | Manualshive

Страница: 113 / 141

background image

WESII User Manual

Manual-WESII-Rev1403
Copyright © KBC Networks 2014

Page 112 of 140

www.kbcnetworks.com

11.2.2.6 Services: SNMP SET UP

The system is compatible with SNMP version 2. This menu option allows you to set up
the SNMP instructions so that the WESII unit can communicate with externally supplied
SNMP devices.

11.2.2.7 Services: NTP SETUP

This menu option is used to set the system to Network Time Protocol which allows
synchronization over a network. The node must be connected to the internet for the NTP
set up to take place. Each node connected via the WESII link can also be set to the same
NTP by using the identical NTP server and gateway IP.

Select the time zone of the node deployment and check the ‘Known Time Server’ box.
Ensure that all the nodes connected are using the same Known Time Server. Select
<Apply> and <Save> to initiate the NTP set up.

«
...
111
112
113
114
115
...
»

Содержание WESII Series














































































































































Отзывы:

Нет отзывов

Похожие инструкции для WESII Series

Бренд: 4IPNET Страницы: 97

Бренд: Palo Alto Network Страницы: 56

Бренд: Ubiquiti Страницы: 3

Бренд: Yamaha Страницы: 6

Бренд: Yamaha Страницы: 4

Бренд: Yamaha Страницы: 22

Бренд: Yamaha Страницы: 49

Бренд: Zonet Страницы: 10

Бренд: Samsung Страницы: 65

Бренд: M86 Security Страницы: 46

Kinetic FLT 80 D5/DDC Body

Бренд: EK-Quantum Страницы: 16

Бренд: Paradyne Страницы: 10

AXP-100H MUSCLE

Бренд: Thermalright Страницы: 36

NetIron MLXe Series

Бренд: Brocade Communications Systems Страницы: 305

Бренд: Idis Страницы: 85

iTRON B 70.2040

Бренд: JUMO Страницы: 41

Бренд: Tait Страницы: 8

Бренд: C4i Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды