Kaysun KEM-30 DNS3 Скачать руководство пользователя страница 40

Страница: 40 / 60

8.6.10 Installation of single or multiple water

pumps

8.6.10.1 DIP switch

The choice of DIP switch see Table 8-6 in detail when single or

multiple water pumps are installed for KEM-30 DNS3 and KEM-60

DNS3.

The choice of DIP switch see Table 8-7 in detail when single or

multiple water pumps are installed for KEM-90 DNS3.

Pay attention to the following problems:

a. If the DIP switch is inconsistent, and the error code is FP, the unit

is not allowed to operate.

b. Only the main unit has the water pump output signal when single

water pump installed, auxiliary units has no water pump output

signal.

c. The water pump control signal is available for both the main unit

and auxiliary units when multiple pumps installed.

8.6.10.2 Installation of water pipe system

a. Single water pump

Piping does not require a one-way valve when single water pump is

installed, refer to figure as follow.

unit (0#)

unit (1#)

terminal

inlet water

outlet water

water pump

unit

(n-1#)

Fig. 8-35 Installation of single water pump

b. Multiple water pumps

Each unit is required to install a one-way valve when multiple pumps

are installed, refer to figure as follow.

unit

(n-1#)

unit (0#)

unit (1#)

terminal

inlet water

outlet water

water pump

one-way valve

Fig. 8-36 Installation of multiple water pump

8.6.10.3 Electric wiring

Only the main unit requires wiring when single water pump installed,

auxiliary units do not require wiring. All of the main unit and auxiliary

units require wiring when multiple water pumps installed. For

specific wiring, see figure 8-19 and 8-20.

9. START-UP AND CONFIGURATION

9.1 Initial start-up at low outdoor ambient

temperature

During initial start-up and when water temperature is low, it is

important that the water is heated gradually. Failure to do so may

result in concrete floors cracking due to rapid temperature change.

Please contact the responsible cast concrete building contractor for

further details.

To do so, the lowest water flow set temperature can be decreased

to a value between 25°C and 35°C by adjusting the FOR

SERVICEMAN. Refer to "FOR SERVICEMAN/special function/

preheating for floor"

9.2 Points for attention prior to trial run

a. After the water system pipeline is flushed several times, please

make sure that the purity of water meets the requirements; the

system is re-filled with water and drained, and the pump is started

up, then make sure that water flow and the pressure at the outlet

meet the requirements.

b. The unit is connected to the main power 12 hours before being

started up, to supply power to the heating belt and pre-heat the

compressor. Inadequate pre-heating may cause damages to the

compressor.

c. Setting of the wired controller. See details of the manual

concerning setting contents of the controller, including such basic

settings as refrigerating and heating mode, manual adjustment

and automatic adjustment mode and pump mode. Under normal

circumstances, the parameters are set around standard operating

conditions for trial run, and extreme working conditions should be

prevented as much as possible.

Содержание KEM-30 DNS3





























































Результаты поиска

Содержание KEM-30 DNS3

Отзывы:

Похожие инструкции для KEM-30 DNS3

Бренды по названию

Популярные бренды

Kaysun KEM-30 DNS3, Инструкция для владельца и по установке

Результаты поиска

Содержание KEM-30 DNS3

Отзывы:

Похожие инструкции для KEM-30 DNS3

Бренды по названию

Популярные бренды