Kaysun KEM-30 DNS3 Скачать руководство пользователя страница 25

Страница: 25 / 60

8.5 Electric wiring

8.5.1 Electric wiring

CAUTIO

1. The air-conditioner should apply special power supply,

whose voltage should conform to rated voltage.

2. Wiring construction must be conducted by the professional

technicians according to the labeling on the circuit diagram.

3. The power wire and the grounding wire must be

connected the suitable terminals.

4. The power wire and the grounding wire must be fasten up

by suitable tools.

5. The terminals connected the power wire and the

grounding wire must be fully fastened and regularly

checked, in case to become flexible.

6. Only use the electric components specified by our

company, and require installation and technical services

from the manufacturer or authorized dealer. If wiring

connection fails to conform to electric installation norm,

failure of the controller, electronic shock, and so on may

be caused.

7. The connected fixed wires must be equipped with

full switching-off devices with at least 3mm contact

separation.

8. Set leakage protective devices according to the requirements

of national technical standard about electric equipment.

9. After completing all wiring construction, conduct careful

check before connecting the power supply.

10. Please carefully read the labels on the electric cabinet.
11. The user’s attempt to repair the controller is prohibited,

since improper repair may cause electric shock,

damages to the controller, and so on. If the user has any

requirement of repair, please contact the maintenance

center.

12. The power cord type designation is H07RN-F.

8.5.2 KEM-30 DNS3 and KEM-60 DNS3

DIP switch, buttons and digital display positions of units.

DSP1

DSP2

Fig. 8-12 Display positions

8.5.3 KEM-90 DNS3

DIP switch, buttons and digital display positions of units.

ENC2

POWER

ENC4

NET_ADDRESS

S12

DSP1

DSP2

Fig. 8-13 Display positions

8.5.4 DIP switch instructions

The definitions for DIP switch of KEM-30 DNS3 and KEM-60 DNS3

are different from those of KEM-90 DNS3. See Table 8-6 for DIP

switch instructions of KEM-30 DNS3 and KEM-60 DNS3, and Table

8-7 for KEM-90 DNS3.

Table 8-6 KEM-30 DNS3 and KEM-60 DNS3

ENC1

0-F

0-F valid for unit address setting

on the DIP switches 0 indicates the

master unit and 1-F the auxiliary units

(parallel connection) (0 by default)

ENC2

0-5

DIP switch for capacity selection

(KEM-30 DNS3 defaults 2)

(KEM-60 DNS3 defaults 5)

S5-1

OFF Normal cooling mode

Valid for S5-1 OFF(factory default)

ON Low-temperature cooling mode

Valid for S5-1 ON

S5-3

OFF Single water pump control

Valid for S5-3 OFF(factory default)

ON Multiple water pumps control

Valid for S5-3 ON

S5-4

OFF Normal control

Valid for S5-4 OFF(factory default)

ON Remote control valid for S5-4 ON

Содержание KEM-30 DNS3





























































Результаты поиска

Содержание KEM-30 DNS3

Отзывы:

Похожие инструкции для KEM-30 DNS3

Бренды по названию

Популярные бренды

Kaysun KEM-30 DNS3, Инструкция для владельца и по установке

Результаты поиска

Содержание KEM-30 DNS3

Отзывы:

Похожие инструкции для KEM-30 DNS3

Бренды по названию

Популярные бренды