background image

 Page 13 

3. Troubleshooting

Issue

Possible Causes

Unit does not turn on when 

pressing ON/OFF button

The unit has a 3-minute protection feature that prevents the unit from overloading. 

The unit cannot be restarted within three minutes of being turned off.

The unit changes from 

COOL/HEAT mode to FAN 

mode

The unit may change its setting to prevent frost from forming on the unit. Once the 

temperature increases, the unit will start operating in the previously selected mode 

again.
The set temperature has been reached, at which point the unit turns off the 

compressor. The unit will continue operating when the temperature fluctuates again.

The indoor unit emits white 

mist

In humid regions, a large temperature difference between the room's air and the 

conditioned air can cause white mist.

Both the indoor and 

outdoor units emit white 

mist

When the unit restarts in HEAT mode after defrosting, white mist may be emitted 

due to moisture generated from the defrosting process.

La unidad interior hace 

ruidos extraños

A rushing air sound may occur when the louver resets its position.
A squeaking sound may occur after running the unit in HEAT mode due to expansion 

and contraction of the unit's plastic parts.

Both the indoor unit and 

outdoor unit make noises

Durante el funcionamiento, se oye un siseo: este sonido corresponde al refrigerante 

que circula por la unidad interior y la unidad exterior.
Low hissing sound when the system starts, has just stopped running, or is defrosting: 

This noise is normal and is caused by the refrigerant gas stopping or changing 

direction.

Squeaking sound: Normal expansion and contraction of plastic and metal parts 

caused by temperature changes during operation can cause squeaking noises.

SAFETY PRECAUTIONS

If ANY of the following conditions occurs, turn off your unit immediately!

•  The power cord is damaged or abnormally warm

•  You smell a burning odor

•  The unit emits loud or abnormal sounds

•  A power fuse blows or the circuit breaker frequently trips

•  Water or other objects fall into or out of the unit

DO NOT ATTEMPT TO FIX THESE YOURSELF! CONTACT AN AUTHORIZED SERVICE PROVIDER IMMEDIATELY!

Common Issues

The following problems are not a malfunction and in most situations will not require repairs.

Содержание KAY-CF 26 DR9





































Отзывы: