KAUP T 406 2H Скачать руководство пользователя страница 5

Страница: 5 / 31

Operating Manual

Original Operating Manual

1.4

CE-Mark

KAUP-Attachments carry the CE-mark. The EC Declaration of Conformity ensures that the
attachment conforms to the EC machinery guideline.

1.5

Qualified and authorised personnel

Qualified and authorised personnel are equipped by way of their education and training to perform
the tasks assigned to them in accordance with accepted practice and safety regulations. They are
assigned tasks by the equipment owner.

1.6

Warranty claims based on defects

KAUP shall not be liable for any damage to the equipment resulting from:

Improper use / operation.

Modifications to components.

Inappropriate installation, maintenance, inspection and servicing.

Assignment of unqualified or non-authorised personnel.

Claims raised by third parties.

1.7

Limits of applicable use

KAUP-attachments are intended for use under the following climatic conditions:

Average ambient temperature for continuous operation:

+25°C

Allowable maximum ambient temperature, short term (up to 1h):

+40°C

Allowable minimum ambient temperature for attachments intended for
indoor use:

+5°C

Allowable minimum ambient temperature for attachments intended for
outdoor use:

-20°C

Standard models of KAUP-attachments are NOT suitable for:

Use in cold storage facilities.

Use in explosive environments.

Use in conjunction with hydraulic systems involving biological oils.

Use in rough environmental conditions (e.g. seawater)

The transport of acidic liquids.

Содержание T 406 2H
































Результаты поиска

Содержание T 406 2H

Отзывы:

Похожие инструкции для T 406 2H

Бренды по названию

Популярные бренды

KAUP T 406 2H, Руководство по эксплуатации

Результаты поиска

Содержание T 406 2H

Отзывы:

Похожие инструкции для T 406 2H

Бренды по названию

Популярные бренды