KAUP 2T458P Скачать руководство пользователя | Manualshive

Страница: 15 / 27

background image

Operating Manual

Original Operating Manual

15

Pay attention to a sufficient load-carrying capacity of the lifting means.

Replace missing or defective warning signs on the attachment.

Do not use third party spare parts. Through poor quality or incorrect matching
they can result in a risk of accident. The EC Declaration of Conformity by the
manufacturer becomes invalid and you assume full responsibility in the case of
accident.

Use only original spare parts from the manufacturer.

The hydraulic system is under pressure. During work on hydraulic components
oil spurting out can cause injuries. Unload the system in accordance with the
operating instructions of the lift truck manufacturer. In the case of injuries caused
by high pressure oil, inform the works physician and seek out a specialist
immediately.

Screw connections can loosen due to vibration of the attachment. During routine
maintenance check that screw connections are correctly torqued and replace
screws which are visibly damaged.

Note the following tightening torques which are valid for screws with connecting surfaces according
to ISO 4762, ISO 4014, ISO 4032 etc.:

Screw / bolt rating

8.8

10.9

12.9

M6 thread

9,3Nm

14Nm

16Nm

M8 thread

23Nm

33Nm

39Nm

M10 thread

45Nm

66Nm

77Nm

Μ12 thread

77Nm

115Nm

135Nm

Μ16 thread

190Nm

280Nm

330Nm

Μ20 thread

385Nm

550Nm

640Nm

Failure of the safety devices (e.g. the pressure relief valve and the non-return
valve) and incorrect connection of the controls to the actuators can cause
malfunctioning of the attachment and damage to it.

After mounting and before initial operation, check the functions and the
identification of the attached equipment with the movement directions of the
operating elements (operating lever, joystick, etc.).

6.2

Significant modification

Significant modifications are, for example, those which affect the stability, performance, speed and
strength of components.

The EC Declaration of Conformity is invalidated by a significant modification of the attachment.

Modifications to the attachment may only be made with prior approval by the manufacturer.

«
...
13
14
15
16
17
...
»

Содержание 2T458P




























Отзывы:

Нет отзывов

Похожие инструкции для 2T458P

GRAPPLE FORK 400

Бренд: Koyker Страницы: 24

Бренд: IMT Страницы: 135

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды