manualshive.com logo in svg

KAUP 2T458P, Руководство по эксплуатации

Поделиться
Скачать
KAUP 2T458P Скачать руководство пользователя страница 14

 

Operating Manual 

 

14 

Original Operating Manual

 

 

5.3 

Driving 

 

 

Make sure the load to be lifted and the pressure plates are in perfect condition.

 

 

Do not drive with the mast tilted forward.

 

 

Take care when driving that neither the attachment nor the load comes into contact 
with the ground. 

 

5.4 

Rotate 

 

 

Rotation can cause damage to the load and the attachment. Ensure sufficient 
distance of the load to the floor, the ceiling, to shelves, etc. 

 

If higher torque than specified is generated by the load, the rotation device 
rotates uncontrolled or not at all. This can lead to damage to the load and the 
attachment. Note the torque given on the type plate of the attachment.

 

 

The torque given on the type plate refers to the pressure difference of 125 bar at the 
hydraulic motor.

 

 

Only rotate loads parallel to the floor (set lifting frame vertically).

 

 

Do not rotate loads if there are people in the working area.

 

 

Rrotate raised loads slowly. Fast rotating can influence the stability of the lift truck.

 

 

6. 

Maintenance and servicing 

6.1 

General 

 
Regular maintenance is essential to ensure reliable operation and long service life of the KAUP 
attachment

.

 

 

 

Ensure that maintenance and servicing are performed by qualified and authorised 
personnel only.

 

 

Lubrication and cleaning work on the attachment may also be performed by the lift truck 
operator.

 

 

Perform maintenance and servicing work only when the attachment is parked securely 
on a stable, level foundation. For installing and removing, it is recommended to use a 
pallet to take the attachment. The attachment can thus be securely placed and 
transported.

 

Содержание 2T458P




























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды