background image

5

PROPER USE

The MobiSet 4 digital CAP 900 is designed to receive digital TV and radio programs via satellite. 
The automatic positioner is intended to be used as a turntable for the Kathrein satellite dish.
The turntable can be used to receive digital TV and radio signals in the frequency range from 10.70 to 
12.75 GHz; the antenna cannot receive terrestrial signals (e.g. DVB-T).

The turntable can only be used in conjunction with the UFS 740sw DVB-S receiver.

In conjunction with this receiver, the turntable provides fully automatic alignment of the satellite dish to 
receive digital satellite signals. The turntable is designed for use in stationary caravans or motor homes.

Any use other than that specifi ed above will void the warranty or guarantee.

The following circumstances result in the loss of all warranty and liability claims towards 
the manufacturer:

• Improper 

installation

• 

Use of non-specifi ed mounting materials, which cannot guarantee the mechanical reliability of the 
antenna system

• 

Impermissible use, e.g. use of the satellite dish for storage

• 

Structural changes or interference with the components and mounting accessories in the set, which 
could endanger both the mechanical and functional reliability

• 

Improper or forcible opening of the components

• 

Use of cleaners containing solvents, such as acetone, nitro-cellulose combination thinner, petrol etc.

• 

Failure to observe installation and safety instructions in this manual

Note:

 

The maximum permissible speed for vehicles with a CAP 900 receiver unit mounted on the 
roof is 130 km/h. Before commencing a journey, the satellite dish must always be lowered into 
horizontal position (park position).

The turntable may be operated in an ambient temperature range of -20 °C to +45 °C. 
Operating the system outside this range may result in malfunctions or damage to the 
system. When choosing the location for installation or raising the UFS 740sw, ensure 
there is adequate ventilation.

PROPER USE (USE FOR THE INTENDED PURPOSE)

The system may be installed only by qualifi ed  specialist 
personnel!

To prevent hazards during installation, operation or when driving on public highways, the 
instructions and information in this manual must be strictly adhered to. Proper installation and 
connection of the system are pre-requisites for conformity with the corresponding standards.
This is documented in advance by the CE mark and the declaration of conformity in the appendix 
to this manual.

Содержание MobiSet 4 digital CAP 900













































Отзывы: