manualshive.com logo in svg
background image

 

 

 

Under NO CIRCUMSTANCE should anyone enter the water while a fountain is operating

The following maintenance procedures can be utilized to ensure many years of quality performance from your Kasco Fountain and 
Light Kit and reduce the need for more costly repair work. 

PROPER INSTALLATION:  Proper installation of Kasco equipment will include a power source with ground fault protection. The control 
panel included with the equipment has built-in ground fault protection for both the fountain and the lighting kit. Ground fault interrupters 
are a safety feature that can also alert you to electrical leaks in the equipment. If you have repeat, consistent trips of the ground fault 
device, the equipment should be disconnected and removed from the water. The power cord should be inspected for damage and you 
should contact your distributor or contact Kasco Marine at 715-262-4488 or [email protected] for further instructions. A 
complete list of control panels can be found in the Accessories section of kascomarine.com. 

OBSERVATION: Operating equipment should be observed on a regular basis (daily, if possible) for any reduction or variation in 
performance. If a change in performance is observed, the equipment should be disconnected from power and inspected.  

WINTER STORAGE: In regions where there is significant freezing in the wintertime, the light kit should be removed from the water to 
protect it from the expansion pressure of ice. Storage over winter is best in a location that is out of the sun and cool, but above 32° F.   

CLEANING: Light kits should be removed from the water at least once per year (at the end of the season in cold climates) to clean the 
exterior of the system. The light fixture surfaces dissipate heat into the water and any algae, calcium, or other build-up will become an 
insulator that blocks heat transfer and may lead to overheating and damage. Keeping the lenses clean will also ensure the brightest 
light possible. 

 

 

Warranty Policy 

Warranty period:  LED3C11, LED4C11, LED6C11 = 2 year Limited Warranty: Kasco® Marine, Inc. warrants this Light Kit to be free 
from defects in material or workmanship under normal use and service. The Kasco Marine, Inc. obligation under this warranty is limited 
to replacing or repairing free of charge any defective part within the warranty period from the date of shipment. Customer shall pay 
shipping charges for returning the unit to Kasco. 

 THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESSED OR IMPLIED, AND ANY OTHER OBLIGATION OR 
LIABILITY WHATEVER ON THE PART OF KASCO MARINE, INC. AND IN NO EVENT SHALL KASCO MARINE, INC. BE LIABLE 
FOR ANY SPECIAL OR CONSEQUENTIAL DAMAGES. 

Warranty is void if:  

 

The Light Kit is not maintained properly according to the Maintenance Recommendations supplied in this Owner’s Manual.

 

 

The lights, control box, or power cord are altered in any way from original shipment.  Cuts in the power cord are not covered 
under warranty. 

 

The Light Kit is damaged by unauthorized tampering. 

Warranty Claim Procedure:

 The best method for establishing warranty period is by keeping your original receipt and registering the 

equipment online at kascomarine.com under the Warranty Information section.  

Once warranty coverage has been established, the light kit may be sent to Kasco Marine or any Kasco Authorized Repair Center for 
evaluation and repair.   

 

Maintenance Recommendations 

 

Warranty 

 

Содержание LED3C11














Отзывы: