manualshive.com logo in svg
background image

 

 

Table of Contents 

 

Important Safety    

 

 

 

 

 

 

 

pg 2 

Parts Included 

 

 

 

 

 

 

 

 

pg 3 

Mounting Instructions 

 

 

 

 

 

 

 

pg 4 - 7 

Maintenance and Warranty 

 

 

 

 

 

 

pg 8 

Repair  

 

 

 

 

 

 

 

 

 

pg 9 

Troubleshooting Tips 

 

 

 

 

 

 

 

pg 10-11 

Replacement Parts  

 

 

 

 

 

 

 

pg 12 

 

Important Safety: 

Please read and follow these important instructions to help ensure your safety and the quality performance of your Kasco 
equipment. 

 

Caution should be used when dealing with any electrical and/or moving equipment. 

 

Under NO CIRCUMSTANCE should anyone enter the water with the electrical equipment plugged in and/or in 
operation.

  

 

Kasco WaterGlow lighting kits are intended for use with a Listed control panel having a GFCI protected receptacle, or 
field wiring terminals and disconnect switch, or a timer with a disconnect for use with a GFCI receptacle. They are 
intended to be mounted on a floating fountain or aerator for use in a natural or man-made body of water to comply 
with NEC Article 682.  

 

Kasco WaterGlow lighting kits have not been evaluated for use in swimming pools, spas or stationary fountains.  

 

LED3C11 kit is 120Vac and MUST be plugged into a GFCI protected receptacle or GFCI protected field terminal 
connections.  

 

LED3C11 fixtures MUST be properly submerged (approx. halfway) to avoid overheating; insufficient submersion or 
operation out of water will damage fixtures and void warranty. 

 

Extreme caution should be used around water, especially cold water, as in Spring, Fall, and Winter, which poses a 
hazard in and of itself.  

 

NEVER lift or drag the equipment by the power cords. If you need to pull the unit to the side of the pond, use the 
anchoring ropes.  

 

Do not use boats that tip easily for lighting kit installation and follow all boating safety rules and regulations, including 
wearing a PFD (Personal Flotation Device). Do not use waders in deep ponds/lakes or ponds/lakes with drop-offs, 
drastic slopes, or soft bottom material. 

 

For more information regarding your control panel instructions, refer to your equipment 

owner’s manual

. A control 

panel must be installed a minimum of 5 feet (3m in Canada) from the body of water unless separated from the body 
of water by a fence, wall, or other permanent barrier that will make the unit inaccessible to persons in the water. A 
complete list of control panels can be found in the Accessories section of kascomarine.com. 

Содержание LED3C11














Отзывы: