Kärcher SC 3 Deluxe EasyFix Premium, Руководство пользователя

Страница: 9 / 36

English 9
For constant steam output, the water has to be topped
up through the cover of the decalcification cartridge.
When topping up the water, the decalcification cartridge
remains secured in the device.
Note
The device is equipped with dry-run protection for the
pump. If the pump runs dry for a longer period, e.g. be-
cause the decalcification cartridge is not correctly in-
serted, the pump switches off and the red water
shortage indicator light flashes.
To be able to operate the device again, the device has
to be switched off and back on again. In the process,
you must make sure that the cartridge has been insert-
ed correctly and there is enough water in the water res-
ervoir.
1. Fill the water reservoir with a maximum of 1 l of tap
water through the cover of the decalcification car-
tridge.
The LED strip lights up in a constant green.
Interrupting operation
In order to save energy, we recommend that you switch
off the device for breaks in operation of longer than 20
minutes.
1. Press the On/Off switch.
Switching off the device
1.
Press the On/Off switch.
Illustration
I
The device has been switched off.
2.
Press the steam lever until no more steam flows out.
The steam boiler is depressurised.
3.
Move the child lock back.
The steam lever is locked.
4.
Remove the mains plug from the socket.
ATTENTION
Device damage due to water putrefaction
If the device is not put into operation for more than 2
months, the water in the reservoir may putrefy.
Drain the water reservoir before breaks in operation.
5. Remove the decalcification cartridge from the de-
vice.
Illustration L
Storing the device
1. Hang the floor nozzle in the park bracket.
Illustration M
2. Connect the extension tubes to the large mounts for
accessories.
3. Connect a manual nozzle and spotlight nozzle to
each extension tube.
4. Wrap the cable and place it in the accessory storage
area.
5. Place the small round brush and power nozzle in the
accessory storage area.
6. Put the steam hose in the accessory storage area.
Illustration N
7. Store the device in a dry location that is protected
from frost.
Important application instructions
Cleaning the floor areas
We recommend sweeping the floor or vacuum cleaning
it before using the appliance. In this way the floor will be
cleared of dirt and loose particles before the wet clean-
ing.
Freshening up textiles
Prior to using the appliance, always check the compati-
bility of the textiles at a concealed point: Steam down
the textile, allow it to dry and then check it for any
change in colour or shape.
Cleaning coated or painted surfaces
ATTENTION
Damaged surfaces
Steam can loosen wax, furniture polish, plastic coatings
or paint and edge band from edges.
Do not direct the steam at glued laminated edges as the
edge band may loosen.
Do not use the appliance for cleaning unsealed wood or
parquet floors.
Do not use the appliance for cleaning painted or plastic
coated surfaces such as kitchen or living room furniture,
doors or parquet.
1. To clean these surfaces, steam a cloth briefly and
use it to wipe over the surfaces.
Glass cleaner
ATTENTION
Glass breakages and damaged surfaces
Steam can damage sealed points of the window frame
and, at low outside temperatures, lead to tension on the
surface of window panes and hence to glass breakages.
Do not direct the steam at sealed points on the window
frame.
At low outside temperatures, heat up the window panes
by gently steaming the full surface of the glass.
 Clean the window area with a manual nozzle and
cover. To remove the water, use a squeegee or wipe
the surfaces dry.
How to use the Accessories
Steam gun
The steam gun can be used for the following applica-
tions without accessories:
● For removing slight creases from the hanging cloth-
ing items: Steam the clothing item from a distance of
10-20 cm.
● For wiping damp dust: Steam a cloth briefly and use
it to wipe over the furniture.
Spotlight nozzle
The spotlight nozzle is suitable for cleaning areas, joins,
fittings, drains, sinks, WCs, blinds or radiators that are
difficult to access. The closer the spotlight nozzle is to
the soiled area, the greater the cleaning efficiency will
be as the temperature and steam volume are at their
highest at the nozzle opening. Larger lime deposits can
be treated before steam cleaning with a suitable deter-
gent. Allow the detergent to soak in for
approx. 5 minutes and then steam it off.
1. Slide the spotlight nozzle onto the steam gun.
Illustration C
Round brush (small)
The small round brush is used for cleaning stubborn dirt.
Stubborn dirt can be removed more easily by brushing.
ATTENTION
Damaged surfaces
The brush may scratch sensitive surfaces.
It is not suitable for cleaning sensitive surfaces.
1. Fit the round brush to the spotlight nozzle.
Illustration D