8
English
19
Crevice brush
20
Manual nozzle
21
Microfibre cover for manual nozzle
22
Extension tubes (2 x)
23
Unlocking button
24
Floor nozzle
25
Hook and loop fastener
26
Microfibre floor cloth (1 x)
27
** Carpet glider
28
** Microfibre floor cloth (2 x)
** optional
Initial start-up
ATTENTION
Device damage due to calcification
The decalcification cartridge only works properly if you
adjust the device to the local water hardness before op-
erating it for the first time.
Set the device to the local water hardness.
Set the device to the current water hardness before us-
ing it in an area with a different water hardness (e.g. af-
ter a move)
1. Insert the decalcification cartridge into the opening
and push it so that it is firmly in place.
Illustration B
2. Set the water hardness, see chapter
.
Installation
Installing accessories
1. Push the open end of the accessory onto the steam
gun so that the unlocking button on the steam gun
engages.
Illustration C
2. Push the open end of the accessory onto the spot-
light nozzle.
Illustration D
3. Connect the extension tubes to the steam gun.
a Push the 1st extension tube onto the steam gun
so that the unlocking button on the steam gun en-
gages.
The connection pipe is connected.
b Push the 2nd extension tube onto the
1st extension tube.
The connection pipes are connected.
Illustration E
4. Push the accessory and / or the floor nozzle onto the
free end of the extension tube.
Illustration F
The accessory is connected.
Disconnecting accessories
1. Move the child lock back.
The steam lever is locked.
2. Push the unlocking button and pull the parts apart.
Illustration G
Operation
Filling water
The water reservoir can be filled at any time.
ATTENTION
Damage to the device
Unsuitable water can block the nozzles or damage the
water level indicator.
Do not use condensation from the clothes dryer for fill-
ing.
Do not use collected rain water for filling.
Do not use cleaning agents or other additives (e.g.
scents) for filling.
1. Fill the water reservoir with a maximum of 1 l of tap
water.
Illustration H
Switching on the device
ATTENTION
Device damage due to incorrectly set water hard-
ness
The decalcification cartridge only works properly if the
device is adjusted to the local water hardness. The de-
vice may calcify if the water hardness is set incorrectly.
Adjust the device to the local water hardness before first
operation, see chapter Setting the water hardness.
Note
When steaming for the first time after removing and re-
inserting the decalcification cartridge, the steam jet may
be weak or irregular, and individual drops of water may
be expelled. The device requires a short running-in pe-
riod in which the decalcification cartridge fills with water.
The steam volume that is expelled increases constantly
until the maximum steam volume has been reached af-
ter approx. 30 seconds.
1. Place the device on a firm surface.
2. Connect the mains plug into a socket.
3. Press the On/Off switch.
4. The LED strip is in fading red.
5. The LED strip lights up in a constant green after ap-
prox.30 seconds.The device is ready for use.
Illustration I
Regulating the steam volume
The expelled steam volume is regulated by pressing the
steam volume button. Two different steam volume but-
tons are available:
Illustration R
Note
The maximum steam volume is always selected when
the device is switched on.
1. Press the steam lever after setting the steam vol-
ume.
2. Before starting cleaning, point the steam gun at a
cloth until steam is expelled evenly.
Topping up the water
If there is a water shortage, the LED strip rapidly flashes
red.
Maximum steam volume
Reduced steam volume
No steam - child lock
Note
In this position, the steam lever cannot
be operated.
Содержание SC 3 Deluxe EasyFix Premium
