background image

TROUBLE SHOOTING

Symptom Cause 

Solution

No gasoline.

Fill gas tank.

Choke is not in correct
position.

Slide choke lever to “CHOKE” 
position.

Low oil level.

Add oil.

Engine throttle is not in 
correct position.

Position the throttle to “FAST”.

Diameter of garden hose is
too small.

Replace with a 3/4 inch garden hose. 

Water supply is restricted.

Check garden hose for kinks, leaks
and blockage.

Not enough inlet water supply.

Open water source full force.

Water inlet filter is clogged.

Remove filter and rinse out in warm
water.

Spray wand is in low 
pressure position.

Turn spray wand tip to high pressure
position.

Not enough inlet water supply.

Turn water on full force. Check garden
hose for kinks, leaks or blockage.

Pump is sucking air.

Check that hoses and fittings are air
tight. Turn off machine and purge
pump by squeezing trigger gun until 
a steady flow of water emerges
through the nozzle.

Water inlet filter is clogged.

Remove filter and rinse out in warm
water.

Discharge nozzle is
obstructed.

Blow out or remove debris with a 
fine needle.

Calcified gun, hose or spray
wand.

Run distilled vinegar through 
detergent suction tube.

10

Pressure built up in the
high pressure washer.

Squeeze the trigger to release the
pressure.

Engine will not
start.

Unit does not reach
high pressure.

Output pressure
varies high and low.

For additional
engine problems
refer to the engine
owners manual.

Model K 1800 IB: 

Slide the throttle control to the 
fast position. Then push primer 
ball three times. Wait 3 seconds
between each push.

Note: in cold weather push 5 times.

Model K 1800 IB:

Engine needs to be primed.

9

CLEANING TIPS 

- continued

Barbecue Grills, Outdoor
Power Equipment & 
Gardening Tools 

(with or without detergent)

Pre-rinse cleaning surface with fresh water. If
using Kärcher All Purpose Cleaner or
Degreaser, place detergent suction tube
directly into cleaning solution and apply
detergent at low pressure. Allow Kärcher
detergent to remain on surface 1-3 minutes.
Do not allow detergent to dry on surface.
Rinse at high pressure keeping the spray
nozzle approximately 3-6 inches from the
cleaning surface. For removing extremely
stubborn dirt, it may be necessary to move
the spray nozzle even closer to the surface
for greater dirt cutting action. To remove
caked on mud from garbage cans, lawn
mower blades, wheel barrels or other 
non-sensitive metal surfaces, you may 
want to use the Kärcher Rotating Nozzle
Spray Wand. 

Caution: Do not use rotating nozzle spray
wand on cloth, plastic or other sensitive
surfaces as it may cause damage.

Patio & Lawn Furniture

(with or without detergent)

Pre-rinse furniture and surrounding area with
fresh water. If using Kärcher All Purpose
Cleaner, place detergent suction tube direct-
ly into cleaning solution and apply to surface
at low pressure. Allow Kärcher All Purpose
Cleaner to remain on surface 1-3 minutes.
Do not allow detergent to dry on surface. If
needed use special Wash Brush Attachment
to remove stubborn dirt. Rinse at high pres-
sure in a sweeping motion keeping the spray
nozzle approximately 3-6 inches from the
cleaning surface. For best results, clean from
top to bottom and from left to right.

Caution: Do not use rotating nozzle spray
wand on patio or lawn furniture as it may
cause damage.

Recommendations

• Before cleaning any surface an inconspicu-

ous area should be cleaned to test spray
pattern and distance for maximum clean-
ing results.

• If painted surfaces are pealing or chipping,

use extreme caution as pressure washer
may remove the loose paint from the 
surface.

OPTIONAL CLEANING ACCESSORIES

Optional cleaning accessories are available to further enhance your cleaning capabilities:
See accessories order form for product descriptions and ordering instructions.

• Rotating Wash Brush

• Wash Brush

• House Washing Wand

• Extension Wand

• Rotating Spray Wand

• Flexible Spray Wand

• Underbody Spray Wand

• Telescopic Spray Wand

• Pipe Drain Cleaner

• Floor Washing Tool

• Sandblasting Attachment

• Detergent Foamer Attachment

• Water Pumping Kit

• Water Suction Hose

• Extension Hose 25’

USA:

1-800-537-4129
www.karcher-usa.com

CAN: 1-800-465-4980

www.karcher.ca

K1800IB/2200IB Washer ManV2.2  9/25/02  6:03 PM  Page 10

Содержание G 1800 K






















Отзывы: