manualshive.com logo in svg

Kärcher BR 30/4 C, Руководство по обслуживанию

Поделиться
Скачать
Kärcher BR 30/4 C Скачать руководство пользователя страница 13

 

English 5.906-434.0 Rev. 00 (12/10)

 13

1 Dirt water reservoir
2 Release, wastewater reservoir

Î

Push the release for the wastewater reservoir 
down and remove the wastewater reservoir from 
the appliance toward the front. 

1 Dirt water reservoir
2 Cover dirt water reservoir
3 Air suction opening
4 Wastewater inlet opening
5 Lock, lid

Î

The lid of the wastewater reservoir houses the air 
suction opening and the wastewater inlet opening.

Î

In order to remove the lid, open the lock and pull 
the lid off the wastewater reservoir upwards.

1 Wastewater inlet opening
2 Water separator
3 Cover dirt water reservoir
4 Seal
5 Floater seal
6 Locking flap
7 Float

Î

The floater is located in the lid. This floater closes 
up the air suction opening and suctioning is no 
longer possible.

Î

The wastewater reservoir needs to be emptied.

With model BR 30/4 C Adv, a suction nozzle can be 
attached to vacuum in corners.

1 Suction pipe holder
2 Suction pipe

Î

Remove the suction pipe from the suction pipe 
holder.

4.5.4 Insert suction nozzle (BR 30/4 C Adv only)

Содержание BR 30/4 C









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды