manualshive.com logo in svg

Kärcher BR 30/4 C, Руководство по обслуживанию

Поделиться
Скачать
Kärcher BR 30/4 C Скачать руководство пользователя страница 11

 

English 5.906-434.0 Rev. 00 (12/10)

 11

Î

To operate, the release of the parking position 
must be pressed (small arrow) and the appliance 
has to be swivelled back simultaneously. The 
parking roller submerges into the cleaning head 
and the brush roller touches the floor.

1 Pedal position, vacuum bar raised
2 Vacuum bar lift pedal
3 Pedal position, vacuum bar lowered

The vacuum bars can be raised or lowered using the 
pedal for the vacuum bar lift.

Note
Turn the appliance off before you activate the suction 
bar lift. Otherwise, the brush drive can be triggered.
The BR 4.300 does not have a suction bar lift.

1 Dirt water reservoir
2 Fresh water tank
3 Wastewater inlet opening with seal
4 Suction pipe
5 Funnel for fresh water inlet
6 Suction air channel
7 Suction air stub with seal

Î

The fresh water reservoir and the wastewater res-
ervoir can be removed to fill, empty and clean the 
appliance.

4.5

Function

4.5.1 Parking/operating position

4.5.2 Raising/lowering the vacuum bar

4.5.3 Removing the tanks

Содержание BR 30/4 C









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды