-
5
We hereby declare that the machine de-
scribed below complies with the relevant
basic safety and health requirements of the
EU Directives, both in its basic design and
construction as well as in the version put
into circulation by us. This declaration shall
cease to be valid if the machine is modified
without our prior approval.
The signatories act on behalf of and with
the authority of the company management.
Documentation supervisor:
S. Reiser
Alfred Kärcher SE & Co. KG
Alfred-Kärcher-Straße 28-40
71364 Winnenden (Germany)
Tel.: +49 7195 14-0
Fax: +49 7195 14-2212
Winnenden, 2018/10/01
The warranty terms published by the rele-
vant sales company are applicable in each
country. We will repair potential failures of
your appliance within the warranty period
free of charge, provided that such failure is
caused by faulty material or defects in man-
ufacturing. In the event of a warranty claim
please contact your dealer or the nearest
authorized Customer Service centre.
Please submit the proof of purchase.
Troubleshooting
Fault
Possible cause
Remedy
of whom
Motor does not turn.
There is no voltage at the motor.
Check fuse, power supply and cables.
Electricians
Thermal protection switch in the coil
has triggered.
Fix cause for overload.
Electricians
Error current protective switch was
triggered.
Remove cause and reset error current protective
switch.
Electricians
Interior cleaner is switched off.
Switch the interior on at the appliance switch.
Operator
Motor does not turn, clean-
ing head does not turn
Drive parts in support pipe broken. Check parts and replace defective parts.
Customer Service
Cleaning head only turns
around one axle or abruptly
Cleaning head touches container
wall.
Change position of cleaning head and make sure
it can run smoothly.
Operator
Excessive tooth play in the bevel
wheels.
Adjust and replace worn parts.
Customer Service
Destroyed gears on bevel wheels. Replace bevel wheels.
Customer Service
Uneven cleaning jet
Spray nozzles clogged.
Clean spray nozzles.
Operator
Spray nozzles damaged.
Replace spray nozzles.
Operator
Spray volume too low.
Leak on the cleaning head or its
supply line.
Check pump, check pressure lines/hoses.
Operator
Filter in the supply line plugged.
Clean filter.
Operator
Significant quantities of
cleaning liquid are leaking
from the drainage borings of
the support pipe.
Slide ring gaskets in the support
pipe are worn.
Check parts and replace defective parts.
Customer Service
Significant pressure loss,
but no cleaning liquid leaks
at the drainage borings
Slide ring gaskets in the cleaning
head are worn.
Check parts and replace defective parts.
Operator
Appliance does not vacuum The suction tube has been installed
wrongly.
Properly screw the suction tube onto the match-
ing connection.
Operator
Wear of the suction nozzle.
Clean suction nozzle.
Operator
Openings for the suctioning of the
water are plugged.
Clean the openings and water passages.
Operator
Although the switching lever
is in the SUCTION position,
water will continue to flow
from the spray nozzles.
Wear of the valve seal.
Replace valve seals.
Customer Service
EU Declaration of Conformity
Product:
Internal cleaner
Type:
BC 14/12
Relevant EU Directives
2014/30/EU
Applied harmonized standards
EN 61000-6-3
EN 61000–3–2: 2014
EN 61000–3–3: 2006
EN 62233: 2008
Chairman of the Board of Management
Director Regulatory Affairs & Certification
Warranty
12
EN
Содержание BC 14/12
