Karat 21042T-WK, Руководство по установке, Страница: 7 / 15

1.打开角阀
查看螺纹连接处密封性，确定不漏水，逆时针旋开角
阀，开口调至最大。
2.接通电源
电源线漏电保护插头插入电源插座，按下复位开关，
插头指示灯亮，表示通电。
3.安全自检
1.主机蜂鸣器一声“嘀”，旋钮亮蓝灯，开始自检；
2.主机蜂鸣器再响一声“嘀”，自检完毕，旋钮亮红灯；
3.功能模式开启，正常使用。
温馨提示：使用前先按下试验按键，复位开关弹起，
指示灯熄灭，表示漏电保护功能正常。
配套角阀
电源指示灯
试验按键
复位开关
电源指示
试验
复位
电源指示
试验
复位
FUNCTIONS OF SEITCH BUTTON 主机旋钮功能说明
Instruction of knob:
[ON/OFF] Long pressing swith knob more than 3 sec.
[FLUSHIING] Switch on → Lightly pressing switch
knob → Flushing
[REAR CLEANING] Switch on → Sit on seat →Rotate
switching knob clockwise to start rear cleaning →
Lightly pressing the knob to stop this action or after 90
sec automaticaly start drying function.
[FEMININE CLEANING] Switch on → Sit on seat →
Rotate switching know anti-clockwise to start
feminine cleaning → Lightly pressing the knob to stop
this action or after 90 sec automaticaly start warm wind
blowing function.
[NOZZLE CLEANING] Switch on, on standby mode,
rotate switching knob clockwise , nozzle extends out
→ Hand cleaning → Rotate switching knob clockwise
again or lightly pressing the knob, nozzle retracts and
stop cleaning.
1. Red light flashes around switch button to
indicate functional mode, blue light flashes around
switch button to indicate energy-saving mode, purple
light flashes around switch button to indicate flushing
mode, no light flashes to indicate standby mode.
2. The default setting of all function is on middle level,
after using controller, shift to the level setted last time.
3.Under rear / feminie cleaning mode, the nozzle
position and water pressure is adjustable by rotating the
switch knob. Long pressing knob switchs the function
inbetween water pressure and nozzle position function.
4.In the warm air condition, please rotate the knob
clockwise to increase the air temperature and
anticlockwise to decrease the air temperature. Press the
knob lightly to stop the heating.
5.Switching knob doesn't function when power is off.
Remark:
OVERALL SKETCH
1. Turn on the angle valve
Check thread connection, make sure no leakage is found,
unscrew angle valve anticlockwise to maximum opening.
3. Self-inspection
Unscrew angle valve anticlockwise to ma The buzzer
rings second “click”, red lightself-inspection is finished;
Start function mode for normal usage.
过滤阀芯的保养
保养时机：当水压正常但冲刷效果不佳时。
1.旋开角阀螺母
2.取出过滤阀芯
3.用牙刷刷洗，清水冲去阀芯内泥沙
4.装回过滤阀芯，重新安装角阀螺母
*建议1-2月清洗一次过滤网
MAINTENANCE OF FILTER NET
Time for maintenance: It is under normal water
pressure but poor flush occurs.
1. Unscrew angle valve nut.
2. Remove filter net.
3. Use the brush to clean filter net.
4. Reinstall filter net and angle valve nut.
*It is recommended that you clean the filter once in
1-2 months
2.Switch the power supply
Insert electric leakage protection plug into power socket,
protection switch,indicator light is on which means there
is electricity. Press electric leakage test button prior to
usage, protection switch bounces to show that protection
function works normally.
旋钮操作说明：
[开/关机] 长按旋钮3秒以上
[冲 水] 开机→轻按旋钮→冲水
[臀 洗] 开机→着坐→顺时 旋钮, 开启臀洗→轻按
旋钮, 结束臀洗或90秒后自动进入暖风功能
[妇 洗] 开机→着坐→逆时 旋钮, 开启妇洗→轻按
旋钮, 结束妇洗或90秒后自动进入暖风功能
[清洗喷嘴]开机,无使用状态下, 顺时 旋钮,喷杆伸出
→手动清洗→再顺时 旋钮或轻按旋钮,喷
杆缩回, 结束清洗。
温馨提示：
1. 机器处于开机状态时，旋钮指示灯亮红灯；处于开
机且节能状态时，旋钮指示灯亮蓝灯；处于坐便器
冲水状态时，旋钮指示灯亮紫灯；处于关机状态时,
旋钮指示灯灭。
2. 刚开机，所有功能档位及喷杆位置设置在中间档，
当使用摇控器后，切换到摇控器显示的功能档位。
3. 在臀、妇洗状态下，通过前后旋转旋钮可调节喷嘴
位置和水压大小.长按旋钮可在水压调节和喷杆位置
调节功能间切换。
4. 在暖风状态下，顺时针旋转风温上升，逆时针旋转
风温降低，轻按旋钮可停止暖风。
5. 断电情况下,旋钮无法使用。
With angle valve
Tips: Press electric leakage test button prior to usage,
protection switch protection function works normally.
Indicator light
Electric leakage
test button
Reset