Karassn KS-858G, Руководство пользователя, Страница: 3 / 31

1.Alarm host 1pc 2.Key 2pcs
3.Remote controller 2pcs 4.Radio antenna 1pc
5.GSM antenna 1pc 6. Double-end telephone line 1pc
7. 2.2KΩline end Resistance 8pcs 8. Screw 2pcs
9.Self tapping Screw 3pcs 10. Plastic Bolt 3pcs
11.User's Manual 1pc 12. Power lead 1pc
The list of standard full kit
1. Introduction
This is a Telephone&GSM/GPRS dual networking Alarm system with LCD display and 4*4 keyboard, and
there are 16 zones (8 wireless zones and 8 wired zones). It works perfectly with remote controllers (up to 8
remote controllers), various wireless/wired detectors, door sensor, manual call point, and wireless/wired
sirens. And they make up a complete safeguard system to guard against theft, fire and gas leakage,
emergency alarm and so on. This alarm host can be stored up to 5 groups of pre-set telephone numbers
(fixed/mobile telephone number). Once alarm happens, the alarm host will activate siren to make alarm
sound immediately, and dial pre-set telephone numbers at the same time, two-way audio after alarm can
be achieved through the optional GSM&GPRS module; mobile APP receives alarm information, remote
control and programming supported; central monitor software receives alarm information, remote control
and programming supported too. It is widely used in residence, marketplace, finance system and
enterprise.
2. Main Functions:
2.1 Support two-way audio.
2.2 Support mobile APP remote control and programming, inquire record. Support central monitor software.
2.3 It is easy to operate with 4*4 keyboard and lattice LCD display.
2.4 Voice pre-recorded, it guides to operate by sound and correctly reports alarm information when alarming.
2.5 There are 8-wired zones and 8 wireless zones altogether, and they share with the zone number.
2.6 8 sub zones can be programmed independently. And the zone list can be set freely in each sub zone, 8 r
emote controllers and 8 user's codes can separately program for 8 sub zones to ARM/DISARM
independently.
2.7 Code classification, 1 installer code, 1 master code, and 8 common user 's codes. Add number 1 at the
end of master code/ common user's code, and then it will become duress code.
2.8 Support to ADEMCO CONTACT ID communication protocol
2.9 5 groups of telephone numbers (mobile and pager number) can be set. Dialing type (tone or pulse) and
appointed communication zone can be programmed. Arm/disarm, whether to report the information of
system state can be set freely.
2.10 It rushes to report alarm information when alarming (the line should be correctly connected)
2.11 Telephone line cut off or short-circuit will send an alarm. (Indicate sound or siren are optional)
2.12 Dial the telephone number, which connected with alarm host to arm/disarm and start alarm on the spot
function remotely through telephone or mobile phone.
2.13 Automatically learn code between Wireless PIR detector, remote controller and alarm host (each zone
can be learned up to 3 detectors, so it can be learned up to 24 detectors and 8 remote controllers
altogether).
2.14 Wired zone respond speed is 50ms-750ms, and the circuit types (Normal Open, Normal Close and
Line-end resistance) can be set freely to connect with all kinds of wired detector.
2.15 Two timers can be set to Arm/Disarm different zones independently.
2.16 Alarm delay time (00-99 seconds) and Arm delay time (00-99 seconds) can be set for appointed zones.
2.17 It has completed self-check function, alarm host/detector disassembly, AC power cut, backup battery
lower of alarm host and detector will activate alarming.
-1-