background image

 

 1 

    

< Note > 

Before replacing the needle, be sure to turn off the machine. 

A clutch motor continues running for a while after the machine is turned off. 

Therefore keep on pressing the pedal until the machine stops. 

1

NEEDLES & THREADING THE MACHINE   

1111----1 Needles

1 Needles

1 Needles

1 Needles    

UY128GAS of Schmetz or Organ 
Select the proper needle for the fabric and thread. 
< Needles and needle size > 

Schmetz Nm65 Nm70 Nm75 Nm80 Nm90 

Organ #09 #10 #11 #12 #14 

 

1111----2 Replacing the needle

2 Replacing the needle

2 Replacing the needle

2 Replacing the needle    

To replace the needle, check the needle carefully to see 
that the scarf is turned to the rear of the machine (see the 
illustration).    Then install the needle correctly. 

 
 
 
 
 

1111----3 Threading the machine

3 Threading the machine

3 Threading the machine

3 Threading the machine    

Thread the machine correctly by referring to the illustration below. 
Threading the machine incorrectly may cause skip stitching, thread breakage and/or 
uneven stitch formation.    Thread tension should be changed according to various kinds of 
conditions such as the thread to be used and/or the feeding amount (see Chapter 10 for 
"Stitch formation"). 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

A

B

C .. Needle threads 

D............... Top cover thread 
E .............. Looper thread 

 

 

Содержание MZ Series























Отзывы: