manualshive.com logo in svg

KANSAI SPECIAL MZ Series, Инструкция по эксплуатации

Поделиться
Скачать
KANSAI SPECIAL MZ Series Скачать руководство пользователя страница 17

 14 

    

8888----2 Stitch length

2 Stitch length

2 Stitch length

2 Stitch length    

The stitch length can be adjusted from 1.4 to 4.2mm 
with no step.  The following table shows the stitch 
length with the number of stitches within 1 inch 
(25.4mm) and 30mm.    

 

Stitch 

Length (mm) 

No. of stitches 

(within 1") 

No. of stitches 

(within 30mm) 

4.2 6.0 7.5 
3.6 7.0 8.0 
2.4 10.5 12.5 
1.4 18.0 21.0 

 

■

To change the stitch length 

1.  To increase the stitch length, turn adjusting 

knob A clockwise.  To decrease the stitch 
length, turn adjusting knob A counterclockwise. 

2.  To adjust the stitch length with lever B, secure 

lever B with nut C as required. 
The range extends from the reading read by 
lever B when adjusting knob A is turned to the 
reading at which lever B is stopped by stopper 
D. 
To adjust the stitch length during sewing, 
connect a chain to the lever. 

 
 
 
 

8888----3 Differential feed

3 Differential feed

3 Differential feed

3 Differential feed    

Remove plug A.    Loosen screw B. 
To gather the fabric, move up screw B (maximum 
normal differential feed ratio: 1:4). 
To stretch the fabric, move down screw B (maximum 
reverse differential feed ratio: 1:0.8). 
When alignment mark C is aligned with the center 
of screw B, the differential feed ratio is 1:1. 

 
 
 
 
 
 

< Note > 

Be sure to turn off the motor before changing the 

stitch length. 

 

 

 

Содержание MZ Series























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды