Kangook Cors-Air Black Bull Скачать руководство пользователя | Manualshive

Страница: 53 / 56

background image

52

Kangook Paramotors User Guide –

February 2020 – V3.0

Copyright 2020 All Rights Reserved.

Accessories



Rescue parachute container is closed and that straps are correctly routed and
attached to the frame. Ensure any accessories are properly connected to the harness
(quick links)



Speed bar fixed to the harness

6.

Checklist

First check :



Weather : Will it rain ? Will the wind speed increase or be gusty above 20km/hr ?



Flight plan : for long distances consider letting a friend know where you are



Airspace authorization (NOTAM) : Is it legal to fly in your chose airspace ?

Final Checklist before take-off:

The  wing  inspection  is  crucial.  Check  the  upper  and  bottom  surface  areas
and that the lines are not damaged. Ensure the risers are in good condition. A
preinflation  of  the  wing  is  important  in  order  to  ensure  none  of  the  lines  are
incorrectly positioned or twisted.

Before take-off, engine on and breaks in hand, final checks:



Leg straps fastened, correctly tightened



Chest strap fastened



Main quick links / carabiners closed and properly closed



Front risers in hand, no twist



Break toggles in hand. No knots nor tangled lines. Lines pass directly
through the pulley system.



Helmet fastened



Flight instruments (radio, GPS, altimeter) fastened and secured



Radio on, volume tested



Avoid engine exhause from blowing on the wing prior to takeoff.

«
...
51
52
53
54
55
...
»

Содержание Cors-Air Black Bull

























































Отзывы:

Нет отзывов

Похожие инструкции для Cors-Air Black Bull

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды