Kangook Cors-Air Black Bull Скачать руководство пользователя | Manualshive

Страница: 4 / 56

background image

3

Kangook Paramotors User Guide –

February 2020 – V3.0

Copyright 2020 All Rights Reserved.

Warning Notice

This manual must be read carefully before using your Kangook product.

Flying a Paramotor has it’s risks but is not dangerous if you respect the following
instructions. That is why our 3 year manufacturing warranty does not cover accidents,
injuries or death.

The regulations concerning the operation of Paramotors / Powered Paragliders (PPG)
will differ according to your home country. It is up to you to be informed about local
licence requirements (if any), laws, rules and regulations.

Always perform a pre-flight check of your aircraft before you take to the sky. You are
the pilot in command. All decisions to fly are yours alone. If your paramotor aircraft
equipment is not working properly do not fly until you correct the issue. You make the
choice to go up in the air but you have no choice about coming down.

1.

Motors and Multi-fit Frame Systems

The unique advantage of the

Kangook

range of products is its frame modularity.

Indeed, most engine types will fit on our frames thanks to our Multifit system.

The chart below describes the main connection templates for the most common
paramotor engines found on the next page.

«
...
2
3
4
5
6
...
»

Содержание Cors-Air Black Bull

























































Отзывы:

Нет отзывов

Похожие инструкции для Cors-Air Black Bull

Бренд: Hacker Motor Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды