Kangook Cors-Air Black Bull Скачать руководство пользователя | Manualshive

Страница: 15 / 56

background image

14

Kangook Paramotors User Guide –

February 2020 – V3.0

Copyright 2020 All Rights Reserved.

a.

Split Leg Harness System

The  Split Leg  Harness can also be used  on your  Kangook  Frame.  The  main benefits
are  its  lightness  as  well  as  the  freedom  of  movements  it  during  the  take-off  and
landing phases of your flight. Perform the following three  steps on both sides of the
harness. Step 1 differs according to the type of harness (Low Hook-In or High Hook-
In).

Step 1: Fix the harness on the hoop. This is for a Low Hook-In.

1 : Put the buckle on the strap

(positioned in the front) as shown.

Stuff the second strap in the back of

the harness or leave 5cm and cut it.

2 : Set up the harness against the frame

and pass the strap under the hoop.

«
...
13
14
15
16
17
...
»

Содержание Cors-Air Black Bull

























































Отзывы:

Нет отзывов

Похожие инструкции для Cors-Air Black Bull

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды