Kamstrup ULTRAFLOW 54 Скачать руководство пользователя страница 56

Страница: 56 / 77

TECHNICAL DESCRIPTION

ULTRAFLOW

54 and 34

5512-385 GB/02.2014/Rev. H1

9.10.2

Hold function

When the Hold input is activated (high level applied to input), counting stops.

When the Hold signal is removed (low level applied to input), counting restarts.

The counters can also be reset by pressing the right key on the front panel (Reset).

Hold input

Galvanically isolated

Input protection

Against reversed polarity

“Open input”

Count (see

Figure 38

)

Figure 38

9.10.3

Push-button functions

Figure

The left push button shifts between readings/counts of the two flow sensor inputs. In the display M1

and M2 respectively indicate the currently displayed flow sensor inputs/counters.

Figure 40. The right push-button resets both counters (M1 and M2).

9.10.4

Using the PULSE TESTER

The PULSE TESTER can be used as follows:

Standing start/stop of flow sensor using the integral pulse counters.

Standing start/stop of flow sensor using the pulse outputs for external test equipment.

Flying start/stop of flow sensor using the integral counters controlled by external equipment (Sample &
Hold).

Flying start/stop of flow sensor using the pulse outputs controlled by external equipment (Sample & Hold).

Содержание ULTRAFLOW 54














































































Результаты поиска

Содержание ULTRAFLOW 54

Отзывы:

Похожие инструкции для ULTRAFLOW 54

Бренды по названию

Популярные бренды

Kamstrup ULTRAFLOW 54, Техническое описание

Результаты поиска

Содержание ULTRAFLOW 54

Отзывы:

Похожие инструкции для ULTRAFLOW 54

Бренды по названию

Популярные бренды