Kamstrup ULTRAFLOW 54 Скачать руководство пользователя страница 45

Страница: 45 / 77

TECHNICAL DESCRIPTION

ULTRAFLOW

54 and 34

5512-385 GB/02.2014/Rev. H1

Diagram 14. Flow sensor tolerances q

1:100 for q

1.5 m³/h.

8.12

Power consumption

The current consumption of ULTRAFLOW

is as follows:

Max. average

50 µA

Max. current

7 mA (max. 40 ms)

8.13

Interface connector/serial data

ULTRAFLOW

54 and 34 is fitted with a four-pole connector under the cover. Thus, it is not possible to access this

connector without breaking the seal. On delivery, the cover will be sealed with a factory seal and in connection
with verified sensors it will be a laboratory seal (legal seal).

The connector is used for:

•

Programming sensor, including adjusting the flow curves by means of METERTOOL

•

Setting the sensor to test mode

•

Reading accumulated water quantity in connection with calibration

•

External control of start/stop in connection with calibration

The interface connector is constructed as shown in

Figure 30

0,01

0,1

[

]

Flow [m³/h]

Flow sensor tolerances qi:qp 1:100 (qp 1.5 m³/h)

EN1434 cl.3

EN1434 cl.2

½ EN1434 cl.2

0,1x qp

0.01

0.1

0.1 x qp

Содержание ULTRAFLOW 54














































































Результаты поиска

Содержание ULTRAFLOW 54

Отзывы:

Похожие инструкции для ULTRAFLOW 54

Бренды по названию

Популярные бренды

Kamstrup ULTRAFLOW 54, Техническое описание

Результаты поиска

Содержание ULTRAFLOW 54

Отзывы:

Похожие инструкции для ULTRAFLOW 54

Бренды по названию

Популярные бренды