Kamstrup MULTICAL 803 Скачать руководство пользователя страница 14

14

Kamstrup A/S • 55122412_A1_GB_2019-03

MULTICAL® 803 & ULTRAFLOW®

6  Connection of power supply

6.1  Mains supply

MULTICAL® 803 is available with supply modules for either 24 VAC/VDC or 230 VAC.
MULTICAL® 803 can be supplied from either 24 VAC/VDC or 230 VAC with cable through the large 
cable connection to the left in the connection base. Use connecting cable with an outer diameter 
of 4-10 mm and ensure correct cable stripping as well as correct mounting of cable relief. If 
connecting to 230 VAC, it is important to make sure that the whole installation complies with 
current regulations. Kamstrup A/S can provide a supply cable to connect the mains supply, in the 
size 2 x 0.75 mm². The supply cable to the meter must never be protected by a larger fuse than 
permitted for any given cable size.
In case of doubt, it is recommended to take advice from an authorised electrician and get an 
individual assessment of the execution of the installation in question. In addition, note that work 
on fixed installations and any intervention in the fuse box must be carried out by an authorized 
electrician only.
For installation in Denmark: See “Installation of mains connected equipment for registration of 
consumption” from the Danish National Safety Board.

Replacement and extension of the mains supply

 

PLEASE MAKE SURE TO DISCONNECT THE MAINS SUPPLY FROM THE CONNECTION PCB 
BEFORE INITIATING THE REPLACEMENT OR EXTENSION OF THE SUPPLY!

The mains supply in MULTICAL® 803 consists of up to three supply modules of protection class 
II, which are connected to the underside of the connection PCB in the meter via a two-wire cable 
with connector at one end and screw terminals at the other. It is possible to connect 2 x 3.6 V 
supply modules to calculator and module slots as well as a 24 VDC supply module to the supply 
of analog outputs or passive third-party flow sensors. Read more in the technical description of 
MULTICAL® 803, document no. 5512-2360.

Note: 

Replacement and extension of the mains supply should always be carried out at a 
workshop.   

Содержание MULTICAL 803





























Отзывы: