4
To disconnect heater turn the control to
OFF, then switch off at the power outlet
then remove plug from its outlet.
Do not insert or allow foreign objects
to pass through the inlet or outlet
openings. This may cause an electric
shock, fire or damage the heater.
To prevent a possible fire or heat damage,
allow ample space around the heater (at
1.7m at front and 0.5m at the rear, top
and sides) and do not totally or partially
block the air inlet or outlets in any
manner. Check the openings from time
to time for accumulated dust. Ensure
long shag carpet does not obstruct
airflow under the unit.
Do not touch hot metal surfaces.
Switch off at the control switch and
power outlet, then unplug and allow
heater to cool down before cleaning or
storing.
Use this heater only as described in this
instruction manual. Any other use not
recommended by the manufacture may
cause fire electric shock or injury and
voids all warranties.
Regularly inspect the supply cord, plug,
control settings, air inlets and outlets
and main housing for any damage. If
found damaged in any way, immediately
cease use of the heater and return to
Kambrook or an authorised service
agent for inspection or repair.
The installation of a residual current
device (safety switch) is recommended
to provide additional safety protection
when using electrical appliances. It is
advisable that a safety switch with a
rated residual operating current not
exceeding 30mA be installed in the
17.
18.
19.
20.
21.
22.
23.
24.
electrical circuit. See your electrician for
professional advice.
HOW TO OPERATE:
Remove your heater from its carton
and associated protective wrapping,
and unwind the cord to its full length
and remove any protective cardboard
or foam that may have been used to
minimize transportation damage. Place
the heater on a firm, level surface in a
stable upright position. Visually inspect
the air inlet and outlets to ensure no
foreign material is blocking these areas.
The heater must always be operated
with the rear air filter in position.
Plug the cord into a 230-240V electrical
outlet. Be sure the plug fits tightly as
a loose fit will cause overheating and
damage the plug. To avoid an electrical
circuit overload, it is recommended that
no other appliances are plugged into the
same circuit with your heater when you
switch the unit on.
This heater has four settings OFF, FAN,
HEAT 1 AND HEAT 2, located at the
top of the unit, along with an adjustable
thermostatic dial for selecting the
desired temperature. HEAT 1 (1000W)
is the lowest heat, HEAT 2 (1800W)
is the highest while selecting the FAN
icon will act to circulate air. When any
of these modes are selected the power
indicator light located at the base of the
heater will illuminate to indicate that
power is on.
Rotating the thermostatic dial will
increase the temperature output of the
unit the higher the dial is turned clockwise
towards the ‘MAX’ symbol.Alternatively,
the
temperature output will decrease
when
the dial is turned anti-clockwise
towards
the ‘MIN‘ symbol.
1.
2.
3.
4.
To turn the heater off, the ‘O’ setting
needs to be selected. This will turn the
heater off, and the power indicator light
will go out.
NOtE: there is a tip over switch
fitted to this heater. When
the heater tips over it will
automatically turn off. the heater
will need to be placed back into
the upright position and the start
sequence and desired temperature
settings selected again.
tHERmO gUaRD
OvERHEatINg SafEtY
DEvICE
Your heater is fitted with a safety device
that switches off the heater in the event
of overheating. Should this heater stop
working, turn off the heater and inspect
for blockages in air inlet or outlets. Wait
at least five minutes for the protection
system to reset before attempting to
restart the heater.
If the heater fails to operate or the
safety device switches off again, return
the heater to your nearest service
centre for examination or repair.
CaRE aND maINtENaNCE
Always turn off and then unplug the
heater before cleaning.
Use only a clean, dry cloth to clean the
external surfaces of the heater only.
If the heater has collected dust or dirt
inside the unit or around the elements,
have the unit cleaned by a qualified
service agent. Do not operate the heater
in this condition.
Do not attempt to open the case of the
5.
•
•
•
•
heater at any time there are no customer
serviceable parts inside.
When not in use, pack the heater,
preferably in its original box for best
protection and store in a cool, clean and
dry location.
The air filter at the rear of the heater
can be easily cleaned by removing the
filter casing panel and removing the
mesh filter. A basic clean in warm water
to remove any build up is adequate and
allow time to completely dry before
replacing the filter and the filter casing
panel.
•
•
