background image

10

 

 CAREFUL!

 During operation of 

the appliance, small hairline cracks 
may develop in the ceramic logs. 
These have no negative impact on 
the operation or flame profile of 
the appliance. Hairline cracks do 
not fall under the warranty.

 

 CAREFUL! 

When heated, the 

gas fires’s internal metal lining 
can expand. This can cause the 
layer of paint on the metal to 
deform, resulting in damage or 
imperfections. The spray paint 
supplied with the gas fire allows 
any paint damage to be fixed.

2.2  Safety related to use

There are risks attached to using a gas 
fire. The temperature of all visible parts 
of the gas fire can rise steeply and there 
is a risk of fire or combustion. Be sure 
that the following safety precautions 
have been taken:

 

 WARNING:

 The gas fire needs a 

permanent power supply. When 
interrupting the power supply, 
previously stored errors are 
deleted. Interrupting the power 
supply regularly affects the safety 
provisions, which can result in 
dangerous situations.

Fire hazard
 

 WARNING

 Make sure that 

flam­

mable materials

 such as curtains 

and furniture are at least 100 cm 
from the fireplace. If a fireguard is 
used, this distance must be at least 
40 cm.

2.  Safety

The following sections provide safety 
information about the gas fire:
-     Safety regulations for decorative 

elements 

-   Safety related to use 
-    Three safety measures for the gas fire 

2.1   Safety instructions for 

decorative elements

 

 FIRE  HAZARD! 

The decorative 

elements must be placed according 
to the instructions. It is prohibited 
to alter the number of decorative 
elements or the configuration 
thereof. Such alterations can lead 
to hazardous situations in terms of 
fire safety.

  
 

 WARNING

 The ignition or 

ionisation rods must be left 
uncovered. Ensure this is the 
case when placing the decorative 
elements. Careless decoration of 
the gas fire can cause incorrect 
ignition, an error code (08A or 08F) 
or a hazardous situation.

 
 

 WARNING

 If the fireplace is 

delivered with the Natural Spark 
Generator, the adhesive tape with 
which the iron filter cap has been 
secured should be removed during 
installation. During installation of 
the fireplace components, the filter 
cap is covered with a ceramic wood 
log or a piece of ceramic charcoal 
(depending on the Kalfire GP 
model).

Содержание G160/41F





































Отзывы: