background image

Optidew User’s Manual

Kahn Instruments

  

vii

Safety

The instrument is designed to be completely safe when installed and operated correctly in 

accordance with the information provided in this manual.

This manual contains all the required information to install, operate and maintain this product. 

Prior to installation and use of this product, this entire manual should be read and understood. 

Installation and operation of this product should be carried out by suitably competent personnel 

only. The installation and operation of this product must be in accordance with the instructions 

provided and according to the terms of any associated safety certificates. Incorrect installation 

and use of this product other than those described in this manual and other than its intended 

purpose will render all warranties void. 

Electricity and pressurized gas can be dangerous. This product must be installed and operated 

only by suitable trained personnel.

No user serviceable parts inside

!

Warnings

!

Where this hazard warning symbol appears in the following sections, 

it is used to indicate areas where potentially hazardous operations 

need to be carried out and where particular attention to personal and 

personnel safety must be observed.

DANGER

Electric

Shock Risk

Where this symbol appears in the following sections it is used to 

indicate areas of potential risk of electric shock.

Electrical Safety

Insure electrical safety is complied with by following the directions provided here and observing all 

local operation & installation requirements at the intended location of use.

 

This product is completely safe when using any options and accessories supplied by the manufacturer 

of this product for use with it. Refer to Section 2 (Installation) of this manual for further details.

Pressure Safety

For this product to operate satisfactorily, pressurized gas must be connected to it. Observe all the 

information contained within this manual and all local operation & installation requirements at the 

intended location of use. Refer to Section 2 (Installation) of this manual for further details.

Содержание Optidew Series

























































































Отзывы: