Kaden KDI42 Скачать руководство пользователя страница 4

4

  |  Kaden Installation Manual

1.  Safety precautions

Read safety precautions before operation and installation

Incorrect installation due to ignoring instructions can cause serious damage or injury.

The seriousness of potential damage or injuries is classified as either a WARNING or CAUTION.

 WARNING

  

Do not

 share the electrical outlet with other appliances. 

Improper or insufficient power supply can cause fire or 
electrical shock.

  

When connecting refrigerant piping, 

do not

 let 

substances or gases other than the specified refrigerant 
enter the unit. The presence of other gases or 
substances will lower the unit’s capacity, and can cause 
abnormally high pressure in the refrigeration cycle. This 
can cause explosion and injury.

  

Do not

 allow children to play with the air conditioner. 

Children must be supervised around the unit at all times.

1.  Installation must be performed by an authorised dealer or 

specialist. Defective installation can cause water leakage, 
electrical shock, or fire.

2.  Installation must be performed according to the 

installation instructions. Improper installation can cause 
water leakage, electrical shock, or fire.

3.  Contact an authorised service technician for repair or 

maintenance of this unit.

4.  Only use the included accessories, parts, and specified 

parts for installation. Using non-standard parts can cause 
water leakage, electrical shock, fire, and can cause the 
unit to fail.

5.   Install the unit in a firm location that can support the unit’s 

weight. If the chosen location cannot support the unit’s 
weight, or the installation is not done properly, the unit 
may drop and cause serious injury and damage. 

6.   Only fully qualified licensed personnel should install, 

service or carry out maintenance to this air conditioning 
unit. All electrical work is to follow local and national 
wiring standards and the Installation Manual.

7.   You must use an independent circuit and single outlet to 

supply power. 

Do not

 connect other appliances to the 

same outlet. Insufficient electrical capacity or defects in 
electrical work can cause electrical shock or fire.

8.   For all electrical work, use the specified cables. Connect 

cables tightly, and clamp them securely to prevent 
external forces from damaging the terminal. Improper 
electrical connections can overheat and cause fire, and 
may also cause shock.

9.   All wiring must be properly arranged to ensure that 

the control board cover can close properly. If the 
control board cover is not closed properly, it can lead 
to corrosion and cause the connection points on the 
terminal to heat up, catch fire, or cause electrical shock.

10. In certain functional environments, such as kitchens, 

server rooms, etc., the use of specially designed air-
conditioning units is highly recommended.

11. This appliance can be used by children aged from  

8 years and above and persons with reduced physical, 
sensory or mental capabilities or lack of experience 
and knowledge if they have been given supervision or 
instruction concerning use of the appliance in a safe way 
and understand the hazards involved. Children must not 
play with the appliance. Cleaning and user maintenance 
must not be made by children without supervision.

This symbol is a CAUTION, and indicates that ignoring instructions may cause moderate injury to your person,
or damage to your unit or other property.

This symbol indicates that you must never perform the action indicated.

This symbol is a WARNING, and indicates that ignoring instructions may cause death or serious injury.

Содержание KDI42









































Отзывы: