Kaba 7102 series страница 4 Скачать руководство пользователя

Страница: 4 / 24

CHECKLIST

Use this checklist to make sure that

everything has been included.

A - Front Lock

C - Dead Bolt 7102 (2

⁄

") or

7108 (2

⁄

") (model specific)

D - Inside Thumbturn Assembly

E - Inside Combination Change Assembly

Screw Pack:

F - Strike Plate

G - 4 thru-bolts (3")

H - 2 (bolt) combination wood/metal screws

I - 4 combination wood/metal screws

J - 4 Thru bolts (2

⁄

K - 4 Thru bolts (2")

Templates (in center of booklet)

DETERMINE THE HAND OF YOUR DOOR

Many of the installation instructions refer to the handing of your door. The hand

of the door is determined with the door in the closed position, from the exterior

or pushbutton side of the door.

A) Right Hand Door. Door opens inward

(push). Hinged on the right side.

B) Left Hand Door. Door opens inward

(push). Hinged on the left side.

C) Right Hand Reverse Door. Door opens

outward (pull). Hinged on the right side.

D) Left Hand Reverse Door. Door opens out-

ward (pull). Hinged on the left side.

LH - Left Hand

RH - Right Hand

LHR - Left Hand Reverse

RHR - Right Hand Reverse

Содержание 7102 series

























Результаты поиска

Содержание 7102 series

Отзывы:

Похожие инструкции для 7102 series

Бренды по названию

Популярные бренды

Kaba 7102 series, Руководство по установке

Результаты поиска

Содержание 7102 series

Отзывы:

Похожие инструкции для 7102 series

Бренды по названию

Популярные бренды