K-Stove EN 14785 Скачать руководство пользователя страница 6

Страница: 6 / 40

K-Stove® is a brand of DMS-Europe BV

NL-3641AR-2 The Netherlands

The heater is mainly made up of

following items - 1. Combustion burn

pot 2. Exhaust fan 3. Room

circulation fan and auger motor.

The following is a list of main

components and their functions:

IGNITER

The HEATER comes equipped with

an automatic electric igniter for

lighting the fuel when the heater is in

lighting mode only. The igniter

remains energized for the first eight

minutes of the lighting sequence.

VACCUM SWITCH

The HEATER has a safety vacuum

switch located behind the left door,

fastened to the base. If a low pressure

is created in the firebox by a leak,

opening the front door, a blocked flue,

or unsealed ash drawer, the vacuum

switch will sense it and cause the heater to go into a shutdown mode.

AUGER AND AUGER MOTOR

The 2 RPM auger motor turns the auger lifting pellets up the auger tube. The pellets are then

dropped down a tube and into the firepot. The auger is controlled by the control board.

OVER TEMPERATURE THERMOSTAT

This safety switch is installed on the bottom of hopper and will shut off the heater if it senses

excessive temperatures (70 degrees).

CONVECTION BLOWER THERMOSTAT

This switch is installed on the vent pipe and turns the convection blower on when the heater

is above 40 degrees.

Содержание EN 14785









































Результаты поиска

Содержание EN 14785

Отзывы:

Похожие инструкции для EN 14785

Бренды по названию

Популярные бренды

K-Stove EN 14785, Инструкция по эксплуатации

Результаты поиска

Содержание EN 14785

Отзывы:

Похожие инструкции для EN 14785

Бренды по названию

Популярные бренды