K-Stove EN 14785 Скачать руководство пользователя страница 34

Страница: 34 / 40

K-Stove® is a brand of DMS-Europe BV

NL-3641AR-2 The Netherlands

problems, start the stove again:

problems

reason

solution

1. The start light or

display does not light

when power is on

No power in stove or in the

control panel.

Check the power and wires.

Fuse is broken

Replace the

fuse

2. The blower doesn’t

work after pressing the

start bottom.

If after stabilization, it

doest work, there must be

wrong

It is normal.

It will start automatically

when the temperature is

above 30 degrees on the

venting pipe.

Please wait

No power in stove or in the

control panel.

Or Unplugged on the mother

board

The low temperature sensor is

broken

Check the power and wires.

Plug it

Replace it

3. No feeding after 20 seconds of starting.

There are three stages for the feeding process.

One is during the several minutes, feeding is constantly. "Feeding" is showing on the LCD

Содержание EN 14785









































Результаты поиска

Содержание EN 14785

Отзывы:

Похожие инструкции для EN 14785

Бренды по названию

Популярные бренды

K-Stove EN 14785, Инструкция по эксплуатации

Результаты поиска

Содержание EN 14785

Отзывы:

Похожие инструкции для EN 14785

Бренды по названию

Популярные бренды