background image

7

K-Line™ G-Set™ Irrigation

Trouble Shooting

Service Information

Setting the Clock

Maintenance

9

10

7

8

Battery Installation

Replace the battery at the start of 
each irrigation season or when the 
low battery 

 

symbol appears. 

Use a 9V alkaline top quality battery 
only. 

1.  Use a Phillips screwdriver to remove 

the 4 battery cover screws.

2.  Remove the battery cover  

and seal.

3. Replace the battery.

4.  After reattaching the seal put the 

cover back and secure with the  

4 screws.

Continue Setting the Irrigation 
duration and 

START

 Times

5.   Use 

 the and 

 to set 

the 

START 1

 minutes.

6. Press 

SET

 to continue

7  Use the 

 and 

 

 to set 

the 

START 1 

hour

8. Press 

SET

 to continue

9.  Repeat steps 

4 - 8

 for 

START 2

You have just adjusted the irrigation program.

Baccara

 products are guaranteed to be free from defects in material and 

workmanship for a period of one year from the date of delivery. 

This guarantee does not apply where equipment is not used and 

installed strictly in accordance with 

Baccara

 specifications and Users 

Guide. Neither does it apply to failures caused by lightning strikes or 

damage due to freezing temperatures or mechanical causes (e.g. lawn 

mowers). 

Baccara

 is not liable for indirect, incidental or consequential 

damage in connection with the use of equipment.

To receive guarantee benefits, customers should return defective units 

along with a copy of the receipt of purchase to the nearest 

Baccara

 

distributor. 

Baccara

 reserves the right to alter, modify or redesign its products, 

pricing and warranty at all times without creating any liability for the 

obsolescence of customer inventory of such parts or products. This 

manufacturer guarantee policy may apply differently in different countries.

Press two long presses 
on the MODE button until 
the time adjustment icon 
appears (the minutes will be 
flashing): 

2.  Use the 

 and 

 buttons to 

adjust minutes.

3. Press 

SET

 to continue

4.  Use the 

 and 

 

 to adjust the hours.

5. Press 

SET

 to return to operating mode. 

Factory Default Setting

The controller comes with the following factory default settings: 
Duration: 10 minutes
Start: 1, 12:00

When replacing seal,  

push seal tabs into slots.

Содержание G-Set













Отзывы: